Altronix Maximal FD Series Dual Power Samar da Wutar Lantarki Samun Jagoran Shigar Masu Sarrafa Wuta

Mafi qarancin FD
- Samar da wutar lantarki 1: 12VDC @ 3.3A ko 24VDC @ 3.6A.
- Samar da wutar lantarki 2: 12VDC @ 3.3A ko 24VDC @ 3.6A.
– Goma sha shida (16) abubuwan da aka kayyade na PTC.
Mafi qarancin FD
- Samar da wutar lantarki 1: 12VDC @ 5.3A ko 24VDC @ 5.6A.
- Samar da wutar lantarki 2: 12VDC @ 5.3A ko 24VDC @ 5.6A.
– Goma sha shida (16) abubuwan da aka kayyade na PTC.
Mafi qarancin FD
- Samar da wutar lantarki 1: 12VDC @ 9.3A.
- Samar da wutar lantarki 2: 12VDC @ 9.3A.
– Goma sha shida (16) abubuwan da aka kayyade na PTC.
Mafi qarancin FD
- Samar da wutar lantarki 1: 12VDC @ 9.3A.
- Samar da wutar lantarki 2: 24VDC @ 9.6A.
– Goma sha shida (16) abubuwan da aka kayyade na PTC.
Mafi qarancin FD
- Samar da wutar lantarki 1: 24VDC @ 9.6A.
- Samar da wutar lantarki 2: 24VDC @ 9.6A.
– Goma sha shida (16) abubuwan da aka kayyade na PTC.

Jagoran Shigarwa
Saukewa: MDFD052419
Kamfanin Shiga: _______________ Wakilin Sabis. Suna: __________________
Adireshi: __________________________ Waya #: __________________

MaximalFD Series Overview:

MaximalFD Samun Wuta/Masu sarrafawa suna rarrabawa da canza wuta don samun damar tsarin sarrafawa da na'urorin haɗi. Suna juyar da shigarwar 120VAC 60Hz zuwa goma sha shida (16) masu sarrafa kayan sarrafawa na 12VDC ko 24VDC PTC masu zaman kansu.
Ana kunna fitar da fitarwa ta wurin buɗaɗɗen mai tattarawa ko kuma buɗe (NO) busasshen shigar da busasshen shigar da bayanai daga Tsarin Gudanarwa, Mai Karatun Card, Maɓalli, Maɓallin Tura, PIR, da sauransu. Raka'a za su tura wuta zuwa na'urori masu sarrafa dama iri-iri ciki har da Mag Locks , Yajin Wutar Lantarki, Masu riƙe da Ƙofa na Magnetic, da dai sauransu. Abubuwan da aka fitar za su yi aiki a cikin yanayin rashin aminci da / ko rashin tsaro. Fuskar FACP tana ba da damar Ƙaddamar Gaggawa, da Kula da Ƙararrawa, ko ana iya amfani da su don jawo wasu na'urori masu taimako. Siffar cire haɗin ƙararrawar wuta ana iya zaɓa ɗaya ɗaya don kowane ko duka na takwas (8).

Jadawalin Kanfigareshan MaximalFD:

Jerin Hukumar:

Abubuwan da aka bayar na UL
Shigarwa na Amurka: UL 294* - UL An Jera shi don Rukunin Tsarin Gudanar da Samun dama.
*ANSI/UL 294 7th Ed. Matakan Ayyukan Gudanar da Samun damar:
Harin Lalacewa - I; Jimiri - I; Tsaron layi - I; Ƙarfin Tsaya - II, III, IV.

Abubuwan da aka bayar na UL
Shigarwa na Kanada: ULC-S319-05 - Kayan aiki na Class I.
CSA C22.2 No.205 - Kayan Aikin Sigina.
ULC-S319-05 Tsarin Kula da Samun Wutar Lantarki za a lalace ta hanyar amfani da kowane ƙari, faɗaɗawa, ƙwaƙwalwar ajiya, ko wani ƙirar ƙira ta masana'anta ko wasu masana'anta.

Siffofin MaximalFD Series:

Modules Masu Kula da Wutar Lantarki ACM8CB:

Goma sha shida (16) suna jawo abubuwan sarrafawa da kansu. Zaɓuɓɓukan fitarwa:
a) Goma sha shida (16) Fail-Safe tace wutar lantarki.
b) Goma sha shida (16) Rashin tsaro tace abubuwan wuta.
c) Duk wani hade na sama.

Goma sha shida (16) Shigar da tsarin sarrafawa yana jawo abubuwan shiga. Zaɓuɓɓukan shigar da kunnawa:
a) Goma sha shida (16) buɗaɗɗen abubuwan shigar da busassun abubuwa (NO).
b) Goma sha shida (16) abubuwan shigar masu tarawa.
c) Duk wani hade na sama.
Goma sha shida (16) tace aux. abubuwan wuta (ana kimanta abubuwan da aka fitar @ 2.5A).

Jajayen LEDs akan allon ACM8CB suna nuna abubuwan da aka kunna kai tsaye (masu kuzari).
Cire haɗin ƙararrawa na Wuta (latching ko rashin latching) ana iya zaɓin ɗaiɗaiku don kowane ko duka na sha shida (16).
Zaɓuɓɓukan shigar da ƙararrawa na Wuta:
a) Buɗewa ta al'ada (NO) ko kuma rufe (NC) busasshen shigar da faɗakarwa.
b) shigarwar juyar da polarity daga da'irar siginar FACP.

Green LED akan allon ACM8CB yana nuna cire haɗin FACP.
Fassarar fitarwa ta FACP yana nuna cewa an kunna shigar da FACP (nau'i na "C" lamba @ 1A/28VDC ba a kimanta ta UL ba).

Samar da Wutar Wuta/Caja na eFlow yana ba da iko gama gari don hukumar ACM8CB (wayoyin masana'antu) da duk na'urorin sarrafa damar shiga (filin wayoyi).
ACM8CB babban fuses an ƙididdige su @ 10A. Ana ƙididdige fitar da PTCs @ 2.5A.

Samar da Wutar Wuta/Caji:

Shigarwa: 120VAC, 60Hz.
Don fitarwa voltage da samar da halin yanzu koma zuwa MaximalFD jerin Kanfigareshan Chart, shafi. 3.
Class 2 na taimako mai iyakataccen fitarwa mai iyaka @ 1A (ba a kunna ba).
Ƙarfafawatage kariya.
Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura masu nau'in gel.
Matsakaicin caji na yanzu 1.54A.
Canja atomatik zuwa baturin jiran aiki lokacin da AC ta gaza. Canja wurin zuwa ƙarfin baturi yana nan take ba tare da katsewa ba.

Cire haɗin Ƙararrawar Wuta da ake kulawa (latching ko mara latching) 10K EOL resistor. Yana aiki akan fararwa na yau da kullun (NO) ko rufaffiyar (NC).
AC ta kasa kulawa (form "C" lambobin sadarwa).
gazawar baturi & kasancewar sa ido (form "C" lambobin sadarwa).
Ƙarfin wutar lantarki. Yana rufe tashoshin fitarwa na DC idan baturi voltage ya faɗi ƙasa 71-73% don raka'a 12V da 70-75% don raka'a 24V (dangane da wutar lantarki). Yana hana zurfafa fitar da baturi.

Don fuse, ƙididdiga suna komawa zuwa Tsarin Kanfigareshan MaximalFD, shafi. 3.
Green AC Power LED yana nuna 120VAC yanzu.
Shigar da AC da alamun fitarwa na LED.
Gajeren kewayawa da kariyar wuce gona da iri.
Wurin yana ɗaukar batir har huɗu (4) 12VDC/12AH.
Girman yadi (H x W x D): 26" x 19" x 6.25" (660.4mm x 482.6mm x 158.8mm).

Umarnin Shigarwa MaximalFD:

Hanyoyin wayoyi za su kasance daidai da Lambar Lantarki ta Ƙasa/NFPA 70/ANSI, Lambar Lantarki ta Kanada, Sashe na I, Sashe na II, kuma tare da duk lambobin gida da hukumomi masu iko. An yi nufin samfurin don amfanin cikin gida kawai.

Kayan Wutar Lantarki LED Diagnostics	(shafi na 7)
Samun damar Mai Kula da Wutar Lantarki LED Diagnostics	(shafi na 7)
Ƙimar Samar da Wutar Lantarki Takaddun Bayanan Baturi	(shafi na 7)
Ƙirar Tasha Tashar Tashar Wuta	(shafi na 8)
Samun Gano Tasha Mai Kula da Wuta	(shafi na 8)
Fitar da Wutar Lantarki Voltage Saituna	(shafi na 9)
Hannun Hannun Aikace-aikacen Mai Gudanar da Wuta	(shafi na 9)
Zane-zane na Ƙirar Ƙimar Ƙarfafawa na FACP/Zaɓi	(shafi na 12)

Dutsen naúrar a wurin da ake so. Yi alama da ramuka a bango don yin layi tare da manyan rijiyoyin maɓalli uku a cikin shingen. Shigar da manyan haɗe-haɗe guda uku da sukurori a bango tare da ɗumbin kawunan suna fitowa. Sanya ramukan maɓalli na sama sama da sukurori uku na sama, matakin, kuma amintattu. Alama matsayi na ƙananan ramuka uku. Cire shingen. Hana ƙananan ramuka kuma shigar da masu ɗaure uku. Sanya ramukan maɓalli na sama sama da sukurori uku na sama. Shigar da ƙananan sukurori guda uku kuma tabbatar da ƙarfafa duk screws (Ƙaƙƙarfan Ƙirar, shafi 15).

Haɗa ƙarfin AC da ba a kunna ba (120VAC 60Hz) zuwa tashoshi masu alama [L, N] (Hoto 3, shafi 10). Green “AC” LED akan allon samar da wutar lantarki zai kunna. Ana iya ganin wannan hasken ta hanyar ruwan tabarau na LED da ke kofar shingen. Yi amfani da 14 AWG ko mafi girma don duk haɗin wutar lantarki. Amintaccen koren waya yana kaiwa zuwa ƙasa.
Kiyaye iyakataccen wayoyi daban da wayoyi marasa iyaka. Dole ne a ba da tazara mafi ƙarancin 0.25 (Fig. 3, shafi 10).
HANKALI: Kar a taɓa sassan ƙarfe da aka fallasa. Kashe wutar da'irar reshe kafin shigarwa ko kayan aiki. Babu sassan da za a iya amfani da su a ciki.
Koma shigarwa da sabis zuwa ƙwararrun ma'aikatan sabis.
Zaɓi fitarwa DC da ake so voltage ta hanyar saita SW1 zuwa matsayi mai dacewa a kan tashar wutar lantarki (Maximal11FD da Maximal33FD), (Fig. 1, shafi 9). Maximal55FD samar da wutar lantarki an saita masana'anta a 12VDC. Maximal77FD samar da wutar lantarki an saita masana'anta a 24VDC. Maximal75FD ya ƙunshi allon samar da wutar lantarki guda ɗaya (1) wanda masana'anta ke saita a 12VDC, da kuma allon samar da wutar lantarki guda ɗaya (1) wanda masana'anta ke saita a 24VDC.

Auna fitarwa voltage na naúrar kafin haɗa kowane na'ura don tabbatar da aiki mai kyau. Ba daidai ba ko high voltage zai lalata waɗannan na'urori.
Zaɓuɓɓukan fitarwa (Hoto 2, shafi 9):
Naúrar za ta samar da ko dai guda goma sha shida (16) da aka canza wutar lantarki, sha shida (16) busasshen nau'in "C", ko duk wani haɗin da aka canza da kuma samar da fitowar "C".
(a) Rashin-Safe Canjin Wutar Wuta: Don Rashin Amintaccen aiki yana haɗa ingantaccen shigarwar (+) na na'urorin sarrafawa zuwa tashar da aka yiwa alama.
[NC]. Haɗa shigarwar mara kyau (-) na na'urorin sarrafa damar shiga zuwa tasha mai alama [COM].
(b) Fail-Secure Canja Wutar Wuta:
Don Aiwatar da Amintaccen aiki haɗa ingantaccen shigarwar (+) na na'urorin sarrafa shiga zuwa tasha mai alama [NO]. Haɗa shigarwar mara kyau (-) na na'urorin sarrafa damar shiga zuwa tasha mai alama [COM].

ACM8CB Abubuwan Wutar Taimako (ba a kunna ba):
Haɗa na'urorin sarrafa damar shiga waɗanda ke buƙatar iko akai-akai zuwa tashoshi masu alama [C] tabbatacce (+) da [COM] korau (-).
Abubuwan Taimako na eFlow (ba a kunna ba):
Don haɗin na'ura mai taimako, wannan fitarwa ba zai shafe shi ta Ƙarƙashin Haɗin Wutar Wuta ko Interface Ƙararrawa ta Wuta. Haɗa na'urar zuwa tasha masu alamar [+ AUX -] (Hoto 3, shafi 10).
Zaɓuɓɓukan shigar da ƙara (Hoto 2, shafi 9):
(a) Kullum Buɗe [NO] shigar da fararwa:
Ana kunna abubuwan shigarwa 1-8 ta hanyar buɗewa ko buɗe abubuwan shigar da ruwa mai tarawa. Haɗa abubuwan sarrafa ikon samun dama, faifan maɓalli, maɓallan turawa, REX PIRs, da sauransu zuwa tashoshi masu alama [IN] da [GND].
(b) Buɗe abubuwan shigar da Mai Tari:
Haɗa kwamitin kula da hanyar shiga buɗaɗɗen mai tarawa tabbatacce (+) zuwa tashoshi masu alama [IN] da korau (-) zuwa tashoshi masu alama [GND].

ACM8CB Zaɓuɓɓukan Interface Ƙararrawar Wuta (Figs. 5-9, shafi 12):
Rufewar [NC] ko buɗe [NO] da aka saba buɗewa daga rukunin kula da ƙararrawa na wuta ko shigarwar juyar da polarity daga da'irar siginar FACP zai shafi abubuwan da aka zaɓa. Don ba da damar cire haɗin FACP don fitarwa kunna kunna (s) masu dacewa [SW1-SW8] KASHE akan kowane allon ACM8CB. Don kashe cire haɗin FACP don fitarwa kunna madaidaicin maɓalli (s) [SW1-SW8] ON akan kowane allon ACM8CB.
(a) Buɗe [NO] yawanci:
Don ƙugiya marasa latching koma zuwa 6, shafi. 12. Domin latching ƙugiya-up koma zuwa siffa 7, shafi. 12.
(b) Akan rufe [NC] shigarwa:
Don ƙugiya marasa latching koma zuwa 8, shafi. 12. Domin latching ƙugiya-up koma zuwa siffa 9, shafi. 12.
(c) FACP Siginar shigar da madauri mai faɗakarwa:
Haɗa tabbataccen (+) da korau (-) daga fitowar sigina na FACP zuwa tashoshi masu alama [+ INP -]. Haɗa FACP EOL zuwa tashoshi masu alama [+ RET -] (an yi la'akari da polarity a cikin yanayin ƙararrawa). Dole ne a yanke jumper da ke kusa da TRG LED (Fig. 2a, shafi 9 da siffa 6, shafi 12).
FACP Dry form “C” fitarwa (ba a kimanta ta UL) (Hoto 2b, shafi 9):
Za a iya amfani da lambobin FACP form “C” don jawo rahoto ko na'urorin sigina. Waɗannan lambobin sadarwa suna canzawa akan shigar da ƙararrawar wuta zuwa allon ACM8CB.

Haɗin Batir na tsaye (Hoto 3, shafi 10):
Don aikace-aikacen Ikon Samun damar Amurka batura na zaɓi ne. Ana buƙatar batura don shigarwa na Kanada (ULC-S319). Lokacin da ba a yi amfani da batura ba, asarar AC zai haifar da asarar juzu'in fitarwatage. Lokacin da ake son amfani da batura masu aiki, dole ne su zama nau'in gubar acid ko gel. Haɗa baturin zuwa tashoshi masu alama [- BAT +] (Fig. 3, shafi 10). Yi amfani da batura guda biyu (2) 12VDC da aka haɗa a jeri don aikin 24VDC (an haɗa da jagororin baturi). Yi amfani da batura - Castle CL1270 (12V / 7AH), CL12120 (12V / 12AH), CL12400 (12V / 40AH), CL12650 (12V / 65AH) batir ko UL-gane BAZR2 da batir BAZR8 na ƙimar da ta dace.
Abubuwan Baturi da Kulawar AC (Hoto 3, shafi 10):
Ana buƙatar haɗa na'urori masu ba da rahoton matsala masu kulawa zuwa abubuwan da aka yiwa alama [AC Fail, BAT Fail] da abubuwan sa ido na sa ido mai alamar [NC, C, NO] zuwa na'urorin sanarwar gani da suka dace. Yi amfani da 22 AWG zuwa 18 AWG don gazawar AC da Ƙananan / Babu rahoton baturi.
Don jinkirta rahoton AC na 2 hrs., saita maɓallin DIP [AC Jinkiri] zuwa matsayin KASHE (Fig. 3, shafi 10).
Don jinkirta rahoton AC don 1 min., saita maɓallin DIP [AC Jinkiri] zuwa matsayin ON (Fig. 3, shafi 10).
Ƙarƙashin Ƙarfin Ƙarfi (Hoto 3, shafi 10):
Don kunna Ƙarshen Ƙarfin Ƙarfin Fitarwa, saita maɓallin DIP [Rufewa] zuwa matsayin ON.
Don kashe Ƙarshen Ƙarfin Wutar Lantarki, saita maɓallin DIP [Rufewa] zuwa matsayin KASHE.
Shigar da Tamper Switch (Hoto 3a, shafi 10):
Dutsen UL Jerin tamper canza (samfurin Altronix TS112 ko daidai) a saman shingen. Zamar da tampmadaidaicin madaidaicin maɓalli a gefen shingen kusan 2” daga gefen dama (Fig. 3a, shafi 10). Haɗa tampcanza wayoyi zuwa shigar da Panel Control Panel ko na'urar da aka jera UL mai dacewa. Don kunna siginar ƙararrawa, buɗe ƙofar shingen.
Abubuwan shigar da wutar lantarki da yawa (Hoto 2, shafi 9) (Ba a kimanta ta UL ba):
Lokacin amfani da ƙarin Fitar da wutar lantarki ta waje, masu tsalle J1 da J2 waɗanda ke kan allon ACM8CB daidai dole ne a yanke (Fig. 2c, shafi 9 da siffa 5, shafi 12). Haɗa Wutar Wutar Lantarki Mai Iyakan Iyaka ta waje zuwa tashoshi masu alamar [- Control +] (Wadannan tashoshi suna daidaitawa da tashoshi na [- Power +]). Lokacin amfani da kayan wuta na DC, dole ne a lura da polarity. Lokacin amfani da kayan wuta na AC, ba a lura da polarity ba (Fig. 2d, shafi 9). Dole ne a yi duk hanyoyin haɗin yanar gizo ta amfani da ma'auni mai dacewa CM ko FPL waya mai jaket (ko madaidaicin daidai) (Hoto 4a, shafi 11).

Kulawa:

Ya kamata a gwada naúrar aƙalla sau ɗaya a shekara don aikin da ya dace kamar haka:

Kulawa na FACP:	Don tabbatar da haɗin kai daidai da aiki na cire haɗin haɗakar ƙararrawa ta Wuta. Da fatan za a bi hanyar da ta dace a ƙasa:
Yawan Buɗe Shigarwa:	Sanya gajere tsakanin tashoshi masu alamar [T] da [+ INP] zai haifar da Kashe Haɗin Ƙararrawar Wuta. Cire gajeriyar don sake saitawa.
Shigarwa Akan Rufe:	Cire waya daga tashar da aka yiwa alama [INP -] zai kunna ƙararrawar wuta Cire haɗin. Sauya waya zuwa tashar da aka yiwa alama [INP -] don sake saitawa.
Shigar da siginar siginar FACP:	Wajibi ne don kunna Tsarin Ƙararrawar Wuta. A cikin duk yanayin da ke sama, koren TRG LED na ACM8CBs zai haskaka. Duk abubuwan da aka zaɓa don Cire haɗin ƙararrawa na wuta zai kunna na'urorin kullewa.

Lura: Duk abubuwan da aka fitar [OUT 1] - [OUT 8] dole ne su kasance a cikin yanayin al'ada (de-mai kuzari) kafin gwaji. Lokacin da aka saita naúrar don Buɗe Al'ada (Hoto 8, shafi 12) ko Kullum Rufewa (Fig. 10, shafi 12) aiki latching, dole ne a sake saita Haɗin Ƙararrawar Wuta ta kunna maɓallin sake saiti na Al'ada Rufe.

Fitarwa Voltage Gwaji:	A ƙarƙashin yanayin kaya na yau da kullun, fitarwar DC voltage ya kamata a duba don daidai voltage matakin (koma zuwa MaximalFD jerin Tsarin Kanfigareshan Shafi na 3).
Gwajin Baturi:	A ƙarƙashin yanayin kaya na al'ada duba cewa an cika baturi, duba ƙayyadadden voltage a tashoshin baturi da kuma tashoshin allon allo masu alamar [+ BAT -] don tabbatar da cewa babu karya a cikin wayoyi masu haɗin baturi.

Lura: Matsakaicin cajin halin yanzu shine 1.54A. Rayuwar baturi da ake tsammanin shine shekaru 5; duk da haka, ana bada shawarar canza batura a cikin shekaru 4 ko ƙasa da haka idan ya cancanta.
Bayanan Wutar Lantarki LED Diagnostics:

Ja (DC)	Green (AC/AC1)	Matsayin Samar da Wuta
ON	ON	Yanayin aiki na al'ada.
ON	KASHE	Asarar AC. Baturi na tsaye yana samar da wuta.
KASHE	ON	Babu fitarwa na DC.
KASHE	KASHE	Asarar AC. An cire ko babu baturi mai jiran aiki. Babu fitarwa na DC.

Ja (Jemage)	Matsayin baturi
ON	Yanayin aiki na al'ada.
KASHE	Baturi gazawa/ƙarancin baturi.

Samun damar Mai Kula da Wutar Lantarki LED Diagnostics:

LED	ON	KASHE
LED 1-LED 8 (ja)	Relay(s) na fitar da kuzari.	Relay(s) na fitar da kuzari.
Trg (Green)	An kunna shigar da FACP (yanayin ƙararrawa).	FACP na al'ada (yanayin rashin ƙararrawa).

Takaddun Takaddun Takaddun Batir na Hukumar Samar da Wuta:

Baturi	Mafi qarancin FD	Mafi qarancin FD	Maximal55FD, Maximal75FD, da Maximal77FD
7AH	Minti 30/4A*	Minti 10/6A	Minti 5/10A
12AH	Minti 35/4A*	Minti 30/6A*	Minti 30/10A*
40AH	Sama da Awa 4/4A*	Sama da Awa 4/6A*	Sama da Awa 2/10A*
65AH	Sama da Awa 4/4A*	Sama da Awa 4/6A*	Sama da Awa 4/10A*

* Waɗannan saitunan kawai za a iya amfani da su a cikin shigarwar ULC-S319.

Ƙirar Tasha Tashar Tashar Wuta:

Labarin Ƙarshe	Aiki/Bayyana
L, G, N	Haɗa 120VAC 60Hz zuwa waɗannan tashoshi: L zuwa zafi, N zuwa tsaka tsaki. Kada a yi amfani da tasha mai alamar [G].
+ DC -	Factory da aka haɗa zuwa allon ACM8.
Ana Kula da Ƙaddamar da EOL	Wuta Ƙararrawa Interface yana jawo shigarwar shigarwa daga gajere ko FACP. Ana iya buɗe abubuwan shigar da ƙara a kullum, yawanci ana rufe su daga da'irar fitarwa ta FACP (shigarwa mai iyaka ta Class 2) (Hoto 3, shafi 10).
A'a, Sake saitin GND	FACP interface latching ko mara latching (Class 2-iyakance ikon) (Fig. 3, shafi 10).
+ AUX-	Ƙarfin Ƙarfi 2 mai iyakataccen fitarwa mai iyaka @ 1A (ba a kunna ba) (Fig. 3, shafi 10).
AC FAIL NC, C, NO	Yana nuna asarar wutar AC, misali haɗi zuwa na'ura mai ji ko ƙararrawa. Relay yawanci yana samun kuzari lokacin da ƙarfin AC ya kasance. Ƙimar tuntuɓar 1A @ 30VDC (Mai iyakacin ƙarfin aji na 2) (Hoto 3), pg. 10).
BAT FAIL NC, C, NO	Yana nuna ƙarancin yanayin baturi, misali haɗi zuwa sashin ƙararrawa. Relay yawanci yana samun kuzari lokacin da ƙarfin DC ya kasance. Ƙimar lamba 1A @ 30VDC. Ana ba da rahoton cire baturi a cikin mintuna 5. An ba da rahoton sake haɗa baturi a cikin minti 1 (iyakantaccen ƙarfin aji 2) (Hoto na 3, shafi. 10).
+ BAT -	Haɗin baturi na tsaye. Matsakaicin cajin na yanzu 1.54A (mara ikon iyaka) (Fig. 3, shafi 10).

Samun Gano Tasha Mai Kula da Wuta:

Labarin Ƙarshe	Aiki/Bayyana
- Power +	12VDC ko 24VDC daga wutar lantarki / caja (ma'aikata da aka haɗa). Waɗannan tashoshi suna daidaitawa da tashoshi na [- Control +].
– Sarrafa +	Waɗannan tashoshi suna daidaitawa da tashoshi na [- Power +]. Ana iya haɗa waɗannan tashoshi zuwa waje Lissafta-iyakantaccen ikon ikon sarrafa wutar lantarki don samar da keɓantaccen ikon aiki don na'urori (Ba a kimanta ta UL ba). Dole ne a cire Jumpers J1 da J2.
TARBIYYA 1- INPUT 8 IN, GND	Daga budewa da/ko buɗaɗɗen abubuwan shigar da mai tarawa (buƙatun fita maɓallan, fita biyu, da sauransu)
FITOWA TA 1- FITARWA 8 NC, C, NO, COM	12VDC zuwa 24VDC yana jawo abubuwan sarrafawa masu sarrafawa. Matsakaicin nauyin kowane fitarwa shine 2.5A.
	Maximal11FD: P/S 1 – 9.8-13.2VDC @ 3.3AP/S 2 – 9.8-13.2VDC @ 3.3A ko P/S 1 – 19.9-26.4VDC @ 3.6AP/S 2 – 19.9-26.4VDC ko @ 3.6-1VDC P/S 9.8 - 13.2-3.3VDC @ 2A da P/S 19.9 - 26.4-3.6VDC @ XNUMXA.
	Maximal33FD: P/S 1 – 9.7-13.2VDC @ 5.3AP/S 2 – 9.7-13.2VDC @ 5.3A ko P/S 1 – 19.8-26.4VDC @ 5.6AP/S 2 – 19.8-26.4VDC ko @ 5.6-1VDC P/S 9.7 - 13.2-5.3VDC @ 2A da P/S 19.8 - 26.4-5.6VDC @ XNUMXA.
	Maximal55FD: P/S 1 – 9.7-13.2VDC @ 9.3A da P/S 2 – 9.7-13.2VDC @ 9.3A.
	Maximal75FD: P/S 1 – 9.7-13.2VDC @ 9.3A da P/S 2 – 19.8-26.4VDC @ 9.6A.
	Maximal77FD: P/S 1 – 19.8-26.4VDC @ 9.6A da P/S 2 – 19.8-26.4VDC @ 9.6A.
	Rashin-Safe [NC tabbatacce (+) & COM Negative (-)], Rashin-Secure [NO tabbatacce (+) & COM Negative (-)], fitarwa na taimako [C tabbatacce (+) & COM Korau (-)]. Lokacin amfani da wutar lantarki AC baya buƙatar kiyaye polarity. Ana nuna lambobin sadarwa a yanayin da ba a kunna ba.
FACP INTERFACE T, + INPUT	Wuta Ƙararrawa Interface yana jawo shigarwa daga FACP. Ana iya buɗe abubuwan shigar da ƙara a kullum, yawanci ana rufe su daga fitowar sigina ta FACP (Figs. 5-9, shafi 12).
FACP INTERFACE NC, C, NO	Form “C” tuntuɓar tuntuɓar mai lamba @ 1A 28VDC don rahoton ƙararrawa (UL ba ya kimanta).

Fitar da Wutar Lantarki Voltage Saituna:

Hannun Hannun Aikace-aikacen Mai Gudanar da Wuta (na kowane ACM8CB):

HANKALI: Lokacin da aka saita allon samar da wutar lantarki don 12VDC yi amfani da baturi ɗaya kawai (1) 12VDC.
Kiyaye iyakataccen wayoyi daban da mara iyaka. Yi amfani da tazara mafi ƙarancin 0.25 inci.
12AH batura masu caji sune manyan batura waɗanda zasu iya dacewa da wannan shingen. Dole ne a yi amfani da shingen baturi na waje mai jera UL idan ana amfani da batura 40AH ko 65AH.

Abubuwan Buƙatun Waya Masu Iyakancin Wutar NEC:

Wayoyin da'ira mai iyaka da mara ƙarfi dole ne su kasance cikin rabuwa a cikin majalisar. Duk wayoyi masu iyakacin wutar lantarki dole ne su kasance aƙalla 0.25” nesa da kowane wayoyi marasa iyaka. Bugu da ƙari, duk na'urorin da'ira mai iyaka da wutar lantarki da na'urorin da ba su da iyaka dole ne su shiga kuma su fita daga majalisar ta hanyoyi daban-daban.
Daya irin wannan example na wannan aka nuna a kasa. Takamammen aikace-aikacen ku na iya buƙatar yin amfani da ƙwanƙwasawa daban-daban. Ana iya amfani da kowane ƙwanƙwasa magudanar ruwa. Don aikace-aikacen iyakantaccen wutar lantarki amfani da magudanar ruwa zaɓi ne. Dole ne a yi duk hanyoyin haɗin yanar gizo ta amfani da ma'auni mai dacewa CM ko FPL waya mai jaki (ko madaidaicin daidai).
Dole ne a sanya shingen UL Listed na zaɓi na zaɓi kusa da wutar lantarki ta hanyoyin wayoyi na Class 1. Don shigarwa na Kanada yi amfani da wayoyi masu kariya don duk haɗin gwiwa.
Lura: Koma zuwa zane mai sarrafa waya a ƙasa don hanyar da ta dace don shigar da waya mai jakin CM ko FPL (Fig. 4a).

Zane-zane na Ƙoƙwalwar FACP:

Bayanan kula:…..

Samar da Wutar Wuta/Caji na iya zama
Sarrafa da Kulawa yayin Ba da rahoto
Ƙarfin / Bincike daga Ko'ina
ta hanyar Network…

LINQ2 - Module Sadarwar Sadarwar Sadarwa
LINQ2 yana ba da damar IP mai nisa zuwa bayanan lokaci na ainihi daga eFlow wutar lantarki / caja don taimakawa ci gaba da tsarin aiki a matakan mafi kyau. Yana sauƙaƙe shigarwa da sauri da sauƙi da saiti, rage girman tsarin lokaci, kuma yana kawar da kiran sabis ɗin da ba dole ba, wanda ke taimakawa rage Jimlar Kudin Mallaka (TCO) - da kuma haifar da sabon tushen Harajin Kuɗi na Watanni (RMR).

Siffofin:
- UL an jera shi a cikin Amurka da Kanada.
- Ikon gida ko nesa har zuwa (2) fitarwar wutar lantarki ta Altronix eFlow guda biyu ta LAN da/ko WAN.
- Saka idanu bincike na lokaci-lokaci: fitowar DC voltage, fitarwa na halin yanzu, AC & matsayin baturi/sabis, canjin yanayin shigar da ke jawo, canjin yanayin fitarwa, da zafin naúrar.
- Ikon samun dama da sarrafa mai amfani: Ƙuntata karantawa/rubutu, Ƙuntata masu amfani zuwa takamaiman albarkatu
– Biyu (2) na cibiyar sadarwa mai sarrafa Form “C” Relays.
- Abubuwan shigar da shirye-shirye guda uku (3): Sarrafa relays da samar da wutar lantarki ta hanyoyin kayan masarufi na waje.
- Imel da sanarwar Windows Dashboard
- Abubuwan tarihin abubuwan da suka faru.
- Secure Socket Layer (SSL).
- Shirye-shirye ta hanyar USB ko web mai lilo – ya haɗa da software mai aiki da kebul na USB ƙafa 6.

LINQ2 Yana hawa Ciki da kowane Rukunin MaximalF

Maximal11FD/33FD/55FD/75FD/77FD Jerin Masu Gudanar da Wutar Lantarki (PTC) Jagoran Shigarwa
Altronix baya da alhakin kowane kuskuren rubutu.
140 58th Street, Brooklyn, New York 11220 USA | waya: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: info@altronix.com | Garanti na rayuwa
IIMaximal11FD/33FD/55FD/75FD/77FD Series
H11 ku

Takardu / Albarkatu

Altronix Maximal FD Series Dual Power Supply Access Controllers [pdf] Jagoran Shigarwa
Matsakaicin FD Series Dual Power Supply Samun Masu Kula da Wutar Lantarki, Matsakaicin FD Jerin, Samar da Wutar Lantarki Dual Masu Kula da Wutar Lantarki, Samar da Wutar Lantarki Dual, Samar da Wutar Lantarki, Masu Gudanar da Wuta, Samar da Wuta, Maximal11FD, Maximal33FD, Maximal55FD, Maximal75FD, FD Maximal77

Magana

Manual mai amfani

Matsakaicin FD Jerin Masu Samar da Wutar Lantarki Biyu