TENMARS TM-195 3-Axis RF Field Strength Meter Instruction Manual

1. Gabatarwa

The TENMARS TM-195 is a 3-axis high-frequency electromagnetic field strength meter designed for measuring and monitoring Radio Frequency (RF) electromagnetic fields. It is capable of measuring frequencies ranging from 50MHz to 3.5GHz. This manual provides essential information for the safe and effective operation of your device.

2. Bayanin Tsaro

Please read and understand all safety instructions before operating the device.

• Kada kayi ƙoƙarin gyara ko gyara na'urar. Koma duk hidima ga ƙwararrun ma'aikata.
• Tabbatar cewa an rufe ɗakin batirin sosai yayin aiki.
• Ka guji fallasa na'urar zuwa matsanancin zafi, zafi, ko hasken rana kai tsaye.
• Tsare na'urar daga filaye masu ƙarfi masu ƙarfi.
• Zubar da batura bisa ga dokokin gida.

3. Samfurin Ya Ƙareview

The TM-195 features a compact design with an integrated 3-axis isotropic sensor for comprehensive RF field strength measurements.

Hoto na 1: TENMARS TM-195 RF Field Strength Meter and Carrying Case. The meter features an orange spherical sensor at the top, a green LCD display showing '360.4 mV/m' and '0945 XYZ', and control buttons below the display. A black carrying case is visible to the right.

3.1. Aka gyara

• 3-Axis Isotropic Sensor: Spherical sensor for comprehensive field detection.
• Nuni LCD: 4-1/2 digits, maximum reading 19999, shows measured values, units, and status indicators.
• Maɓallan sarrafawa: For power, mode selection, unit change, data hold, alarm settings, and data memory.
• Dakin Baturi: Located at the rear for 9V battery.

3.2. Nuni Manuniya

• XYZ: Indicates triaxial measurement mode.
• mV/m, V/m, µA/m, mA/m, µW/m², mW/m², µW/cm²: Ƙungiyoyin aunawa.
• MAX/AVG: Maximum and Average value indicators.
• RIKE: Data hold function active.
• ADAM: Alarm function active.
• Ikon baturi: Yana nuna matakin baturi.

4. Saita

4.1. Shigar da Baturi

1. Bude murfin sashin baturi a bayan na'urar.
2. Insert a new 9V battery (NEDA 1604, IEC 6F22, or JIS 006P), observing polarity.
3. Rufe murfin ɗakin baturi amintacce.

4.2. Ƙarfin Farko Kunna

Danna maɓallin Ƙarfi button (labeled with a circle and vertical line) to turn on the device. The display will illuminate and show the current RF field strength.

5. Umarnin Aiki

5.1. Kunnawa / Kashewa

• Don kunnawa, danna maɓallin Ƙarfi maballin.
• Don kashe wuta, latsa ka riƙe Ƙarfi maɓalli na kusan daƙiƙa 2.

5.2. Measurement Modes (MAX/AVG)

Danna maɓallin MAX/AVG button to cycle through measurement display modes:

• Instantaneous Value: Displays the current real-time measurement.
• Maximum Value (MAX): Displays the highest value recorded since power-on or reset.
• Average Value (AVG): Displays the average value recorded over time.
• Maximum Average Value (MAX AVG): Displays the maximum of the averaged values.

5.3. Zaɓin Ƙungiya

Danna maɓallin UNIT/ENTER button to change the measurement unit. Available units include:

• mV/m (millivolts per meter)
• V/m (volts per meter)
• µA/m (microamperes per meter)
• mA/m (milliamperes per meter)
• µW/m² (microwatts per square meter)
• mW/m² (milliwatts per square meter)
• µW/cm² (microwatts per square centimeter)

5.4. Data Hold (HOLD/ALARM)

Danna maɓallin HOLD/ALARM button briefly to freeze the current reading on the display. Press again to release.

5.5. Ayyukan ƙararrawa

Don saita iyakar ƙararrawa:

1. Latsa ka riƙe HOLD/ALARM button for approximately 2 seconds to enter alarm setting mode.
2. Yi amfani da MAX/AVG kuma REC/TIME buttons to adjust the threshold value.
3. Latsa UNIT/ENTER don tabbatarwa da ajiye saitin.
4. The audible buzzer alarm will activate if the measured value exceeds the set threshold.

5.6. Data Memory (XYZ/MEM)

The device supports manual storage of up to 200 data sets.

1. To save a reading, press the XYZ/MEM button briefly. The current reading will be stored.
2. Don tunawa da bayanan da aka adana, latsa ka riƙe XYZ/MEM button for approximately 2 seconds. Use the MAX/AVG kuma REC/TIME buttons to navigate through stored records.
3. Latsa UNIT/ENTER to exit data recall mode.

5.7. Calibration Factor (CAL) Adjustment

The calibration factor can be adjusted if necessary. Refer to the SET button and its associated menu for this advanced setting. This feature allows for fine-tuning the meter's response.

5.8. Powerarfin Autoarya

The device has an adjustable auto power-off function. The default time is 15 minutes. To adjust this setting:

1. Latsa ka riƙe SET maballin don shigar da menu na saitunan.
2. Navigate to the auto power-off option using the MAX/AVG or REC/TIME maɓalli.
3. Yi amfani da MAX/AVG kuma REC/TIME buttons to set the desired time (0 to 99 minutes).
4. Latsa UNIT/ENTER to confirm and save. Setting to 0 disables auto power-off.

6. Kulawa

• Tsaftace na'urar tare da laushi, bushe bushe. Kada a yi amfani da masu tsabtace abrasive ko kaushi.
• If the device will not be used for an extended period, remove the battery to prevent leakage.
• Ajiye na'urar a wuri mai sanyi, bushe, nesa da hasken rana kai tsaye da matsanancin zafi.

7. Shirya matsala

• Na'urar baya kunnawa: Duba shigar da batirin kuma tabbatar da cewa batirin yana da isasshen caji. Sauya idan ya cancanta.
• Karatu marasa daidaituwa: Ensure the device is held steady and away from large metallic objects or other strong RF sources that might interfere with measurements. Verify the selected unit is appropriate for the measurement range.
• Ƙararrawa baya ƙara: Check if the alarm function is enabled and the threshold is set correctly.
• Nuni ba komai bane ko duhu: Sauya baturin.

8. Ƙayyadaddun bayanai

9. Garanti da Tallafawa

For warranty information and technical support, please refer to the documentation provided with your purchase or contact TENMARS customer service. Keep your purchase receipt as proof of purchase.