Simplex 4099-9006 Double Action, Push Pull Down Fire Alarm Station

1. Gabatarwa

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Simplex 4099-9006 Double Action, Push Pull Down Fire Alarm Station. This device is designed to initiate a fire alarm signal when manually activated, contributing to the overall safety and security of a building's occupants.

The Simplex 4099-9006 is an IDNet addressable manual pull station with an integrated LED indicator, ensuring reliable communication within compatible fire alarm systems.

2. Bayanin Tsaro

WARNING: Installation and servicing of this device must be performed by qualified personnel only, in accordance with all local and national electrical codes, and the National Fire Alarm and Signaling Code (NFPA 72).

• Always disconnect power to the fire alarm control panel before installing or servicing the pull station.
• Tabbatar da ƙasa mai kyau don hana girgiza wutar lantarki.
• Do not paint over the pull station or obstruct its operation.
• Test the pull station regularly as part of a comprehensive fire alarm system testing schedule.
• This device is not intended for outdoor use unless specifically rated for such environments.

3. Samfurin Ya Ƙareview

The Simplex 4099-9006 is a robust, red-colored manual fire alarm pull station featuring a double-action mechanism (push then pull). It includes an integrated LED indicator for status feedback.

Figure 3.1: Simplex 4099-9006 Double Action Fire Alarm Pull Station. This image displays the front of the red pull station with "FIRE ALARM" and "PUSH PULL DOWN" labels, alongside a detailed instruction sheet for installation and mounting, and a small bag of mounting hardware.

Mabuɗin abubuwan haɗin gwiwa sun haɗa da:

• Activation Handle: The "PUSH PULL DOWN" mechanism used to initiate an alarm.
• Alamar LED: Provides visual status of the device (e.g., normal, alarm, trouble).
• Toshe Tasha: For connecting to the fire alarm control panel's IDNet circuit.
• Mounting Plate/Housing: Secures the device to a standard electrical box or surface.

4. Saita & Shigarwa

The Simplex 4099-9006 pull station can be installed using either single-gang or two-part mounting methods, typically on a standard 4-inch square electrical box (not supplied).

4.1 Pre-Ininstalling Checks

• Verify that the fire alarm control panel is powered off.
• Ensure the mounting location is clean, dry, and meets local code requirements for height and accessibility.
• Confirm all necessary tools and hardware are available (e.g., screwdriver, wire strippers, mounting screws).

4.2 Hanyoyi na hawa

Refer to the installation diagrams provided with the product and shown in Figure 3.1 for visual guidance.

4.2.1 Single-Gang Mounting

1. Secure the pull station directly to a standard single-gang electrical box.
2. Ensure the device is flush with the wall surface.

4.2.2 Two-Part Mounting

1. Install the backbox or mounting plate first, typically a 4-inch square electrical box.
2. Mount the pull station assembly onto the installed backbox.
3. This method may be used for flush trim or surface mounting applications.

4.3 Wayoyi

The 4099-9006 is an IDNet addressable device. Connect the pull station to the IDNet circuit of the fire alarm control panel using appropriate gauge wiring, following the wiring diagram provided on the device or in its specific installation sheet. Ensure polarity is correct.

• Connect the incoming and outgoing IDNet circuit wires to the designated terminals.
• Tabbatar cewa duk hanyoyin haɗin suna amintacce kuma ba su da guntun wando.

4.4 Bayan Shigarwa

• Once installed and wired, restore power to the fire alarm control panel.
• Verify the LED indicator on the pull station shows a normal operating status (typically a slow flash).
• Perform a functional test of the pull station as described in the "Operating Instructions" section.

5. Umarnin Aiki

The Simplex 4099-9006 features a double-action activation mechanism to prevent accidental alarms.

5.1 Activating the Alarm

1. TURA: Firmly push the "PUSH" bar located at the top of the activation handle.
2. PULL DOWN: Once the "PUSH" bar is depressed, pull the handle "PULL DOWN" until it latches in the alarm position.
3. Upon activation, the pull station will send an alarm signal to the fire alarm control panel, and the integrated LED will illuminate steadily (or change to a rapid flash, depending on system programming) to indicate an alarm state.

5.2 Resetting the Pull Station

To reset the pull station after an alarm, a special key (not included with this specific model, as indicated by "No Key" in the product title, implying a different reset mechanism or system-level reset) or tool is typically required to return the handle to its normal, non-alarm position. For the 4099-9006, the reset mechanism is internal and does not require a key. Simply push the handle back into its original position. The fire alarm control panel must also be reset to clear the alarm condition from the system.

6. Kulawa

Regular maintenance ensures the reliable operation of your Simplex 4099-9006 pull station. All maintenance should be performed by qualified personnel.

6.1 Dubawa na yau da kullun

• Visual Inspection (Monthly): Check for any physical damage, obstructions, or signs of tampering. Ensure the pull station is clean and clearly visible.
• LED Status (Monthly): Verify the LED indicator is showing a normal operating status (e.g., slow flash).

6.2 Functional Testing (Annually or as per local codes)

Functional testing should be conducted by a certified fire alarm technician.

1. Notify building occupants and the monitoring station before testing.
2. Activate the pull station as described in "Operating Instructions".
3. Verify that the fire alarm control panel receives the alarm signal and initiates appropriate responses (e.g., sounding alarms, notifying monitoring station).
4. Reset the pull station and the fire alarm control panel.
5. Confirm the pull station returns to a normal operating state.

6.3 Tsaftacewa

Tsaftace wajen tashar ja da taushi, damp zane. Kada a yi amfani da masu tsabtace abrasive ko kaushi, saboda waɗannan na iya lalata ƙarshen ko abubuwan ciki.

7. Shirya matsala

This section addresses common issues you might encounter with the Simplex 4099-9006 pull station. For complex issues, contact a qualified fire alarm technician.

8. Ƙayyadaddun bayanai

Figure 8.1: Product packaging for the Simplex 4099-9006, showing the brown cardboard box with product identification labels. The labels confirm PID 4099-9006 and Part No. 06501211.

9. Garanti & Tallafi

9.1 Bayanin Garanti

This Simplex product is typically covered by a manufacturer's warranty against defects in materials and workmanship. Specific warranty terms and duration may vary. Please refer to the original purchase documentation or contact Simplex customer service for detailed warranty information.

Note: The product listing mentions "12 months warranty" and "30 days return if not satisfied". This information is from a third-party seller and may not reflect the official manufacturer's warranty. Always verify with the manufacturer.

9.2 Tallafin Fasaha

For technical assistance, installation guidance, or troubleshooting beyond the scope of this manual, please contact a certified fire alarm technician or the manufacturer directly.

Simplex Customer Support: Please visit the official SimplexGrinnell webshafin yanar gizo ko duba marufin samfurin ku don cikakkun bayanai game da hulɗa.

Don tambayoyi na gabaɗaya, zaku iya duba Simplex brand page on Amazon.