1. Gabatarwa
This manual provides essential information for the installation, operation, and maintenance of the BANNER ENGINEERING S18AW3FF50 EZ-Beam S18 Series Photoelectric Sensor. This sensor is designed for reliable object detection in industrial environments, featuring a 50 mm range, 20-250VAC input, and SPST solid-state light operate output.
Figure 1: BANNER ENGINEERING S18AW3FF50 Photoelectric Sensor with coiled cable.
2. Saita da Shigarwa
Proper installation is crucial for optimal performance and safety. Follow these steps carefully.
2.1 Cire kaya da dubawa
- Carefully remove the sensor from its packaging.
- Inspect the sensor for any visible damage that may have occurred during shipping.
- Tabbatar cewa duk abubuwan da aka jera a cikin takardar tattarawa suna nan.
2.2 Hawan Sensor
The S18AW3FF50 sensor is designed for easy mounting. Ensure the mounting surface is stable and free from excessive vibration.
- Select a mounting location that provides clear line-of-sight for the sensor's detection range (50 mm).
- Secure the sensor using appropriate mounting hardware (not included). The sensor features a threaded barrel for secure attachment.
- Ensure the sensor is oriented correctly for the intended detection application.
Hoto 2: Gefe view of the S18AW3FF50 sensor, showing the threaded barrel and cable.
2.3 Haɗin Wutar Lantarki
GARGADI: Disconnect all power before making electrical connections to prevent electric shock or damage to the equipment.
The S18AW3FF50 operates on 20-250VAC input and provides an SPST Solid-State Light Operate output. The sensor comes with a 2M (6.5FT) cable.
| Launin Waya | Aiki |
|---|---|
| Brown | AC Line (L1) |
| Blue | AC Neutral (L2) |
| Baki | Output (SPST Light Operate) |
Connect the sensor wires to the control circuit according to the provided wiring diagram and local electrical codes. Ensure all connections are secure.
Figure 3: S18AW3FF50 sensor showing the cable with exposed wires for electrical connection.
3. Aiki
Once installed and wired, the S18AW3FF50 sensor is ready for operation.
3.1 Kunnawa
Apply power to the sensor (20-250VAC). The sensor will typically have an indicator LED (if present) to show power status and output state.
3.2 Detection Principle
The S18AW3FF50 is a photoelectric sensor operating in a fixed field mode. It emits a light beam and detects objects based on the reflection or interruption of this beam. The "Light Operate" output means the output will be active when light is received by the sensor (i.e., when an object is detected or not detected, depending on the specific fixed field configuration).
3.3 Range and Performance
The sensor has a specified detection range of 50 mm. Ensure that objects to be detected fall within this range for reliable operation. Environmental factors such as dust, moisture, and ambient light can affect performance.
4. Kulawa
The S18AW3FF50 sensor is designed for low maintenance. Regular checks can ensure long-term reliable operation.
4.1 Tsaftacewa
- Periodically clean the sensor lens and housing to remove dust, dirt, or debris that may accumulate and interfere with detection.
- Use a soft, lint-free cloth and a mild cleaning solution if necessary. Avoid abrasive cleaners or solvents.
4.2 Cable and Connection Inspection
- Regularly inspect the sensor cable for any signs of wear, cuts, or damage.
- Check electrical connections to ensure they remain secure and free from corrosion.
5. Shirya matsala
This section provides solutions to common issues encountered with the S18AW3FF50 sensor.
| Matsala | Dalili mai yiwuwa | Magani |
|---|---|---|
| Firikwensin ba ya kunnawa | No power supply; Incorrect wiring; Damaged sensor. | Verify power supply (20-250VAC); Check wiring against Table 1; Replace sensor if damaged. |
| Na'urar firikwensin ba ta gano abubuwa ba | Object out of range (50 mm); Dirty lens; Misalignment; Ambient light interference. | Ensure object is within 50 mm range; Clean sensor lens; Realign sensor; Shield sensor from strong ambient light. |
| Ganowa akai-akai | Vibration; Loose connections; Fluctuating power. | Secure sensor mounting; Check all electrical connections; Ensure stable power supply. |
6. Ƙayyadaddun bayanai
Key technical specifications for the BANNER ENGINEERING S18AW3FF50 Photoelectric Sensor.
- Samfura: Saukewa: S18AW3FF50
- Jerin: EZ-Beam S18 Series
- Tsawon Ganewa: mm50 ku
- Shigar da Voltage: 20-250VAC
- Nau'in fitarwa: SPST Solid-State Light Operate
- Tsawon Kebul: 2M (6.5FT)
- Nau'in Sensor: Photoelectric, Fixed Field
- Mai ƙira: BANNER ENGINEERING
- ASIN: B07RZTBRLS
- Kwanan Wata Farko Akwai: Disamba 3, 2021
7. Garanti da Tallafawa
For warranty information and technical support, please contact BANNER ENGINEERING directly or refer to their official website.
Manufar Komawa: The product may be subject to a return policy of 30 days for refund/replacement, as per the seller's terms.
Mai ƙira: BANNER ENGINEERING
Don ƙarin taimako, ziyarci BANNER ENGINEERING official website.
