Ƙarfafa B2-SSCT Tsayayyen Frame Guda

Ƙayyadaddun bayanai

• Table feet: 2 guda
• Centre bracket: 1 pc
• Column (right): 1 pc
• Center rails: 2 guda
• Allen Wrench (4mm): 1 pc
• Allen Wrench (5mm): 1 pc

Umarnin Amfani da samfur

Umarnin Majalisa

1. Mataki 1: Sauke ƙusoshin da aka riga aka shigar kuma daidaita tsayin firam ɗin saman don dacewa da girman saman tebur.
2. Mataki 2: Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Mataki 3: Place the table feet on the Column, rotate it to align, then tighten the pre-installed bolt.
4. Mataki 4: Sanya madaidaicin gefe a saman firam ɗin kuma ƙara maƙallan.
5. Mataki 5: Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10. Tighten the pre-installed bolts on the top frame.

Shigar da Tire na Cable

1. Mataki 1: Fix the cable tray (B2-SSCT) to the cable tray arms (B2-SSARM) with 8 pcs M6x10 screws.
2. Mataki 2: Shigar da maƙallan U zuwa firam ɗin tebur tare da pcs 4 M8x10 sukurori. Dutsen tire na USB zuwa firam ɗin tebur kuma gyara shi da 6 inji mai kwakwalwa M6x10.

Shigar da Panel ɗin allo (Allon Sirri na Shush30)

1. Mataki 1: Insert the tapped plates into the screen panel (plates can be found in the B2-SBRAC carton).
2. Mataki 2: Shigar da maƙallan allo (B2-SBRAC) zuwa Shush30 Extrusion tare da pcs 8 M5x6 sukurori.
3. Mataki 3: Gyara ɓangarorin allo (B2-SBRAC) zuwa firam ɗin tebur tare da pcs 10 M6x10 sukurori.

Eco Panel Screen Panel Installation

1. Mataki 1: Install the screen brackets (B2-SBRAC) on the cable tray arm (B2-SSARM) with 10 PCS M6x10 Screws. The direction as the photos display.
2. Mataki 2: Place the EPS panel on the screen brackets using a 6mm drill bit (not included), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes.
   • Place 8 x Double Ended Bolts M5*32mm -6mm through the screen bracket (B2-SBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with an Allen key.

sassan sassa

A'A.	Sunan Bangaren	PCS
1	Ƙafafun tebur	2
2	Rukunin (dama)	1
3	Saukewa: M6X12	5
4	Saukewa: ST4X20	22
5	Maƙallan gefe	2
6	Rubutun roba	14
7	Babban firam-1	1
8	Saukewa: M6X10	3

A'A.	Sunan Bangaren	PCS
9	Bakin tsakiya	1
10	Rails na tsakiya	2
11	Babban firam-2	1
12	Rukunin (hagu)	1
13	Allen Wrench (4mm)	1
14	Allen Wrench (5mm)	1
15	Kebul Tie	5

Umarnin Majalisa

1. Mataki na 1
   • Sauke ƙusoshin da aka riga aka shigar kuma daidaita tsayin firam ɗin saman don dacewa da girman saman tebur.
2. Mataki na 2
   • Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Mataki na 3
   • Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
4. Mataki na 4
   • Sanya madaidaicin gefe a saman firam ɗin kuma ƙara maƙallan.
5. Mataki na 5
   • Dutsen tebur ɗin kuma gyara shi tare da 14 inji mai kwakwalwa ST4x20;
   • Fix the centre bracket with 2 pcs of screws M6x10.
   • Tsara ƙusoshin da aka riga aka shigar a saman firam ɗin.

Shigar da tire na USB

1. Mataki na 1
   • Gyara tiren kebul (B2-SSCT) zuwa hannun tire na USB (B2-SSARM) tare da pcs 8 M6x10 sukurori.
   • Mataki na 2
   • Shigar da maƙallan U zuwa firam ɗin tebur tare da pcs 4 M8x10 sukurori.
   • Dutsen tire na USB zuwa firam ɗin tebur kuma gyara shi tare da pcs 6 M6x10

Shigar da panel panel ( Shush30 Privacy Screen )

1. Mataki na 1
   • Insert the tapped plates into the screen panel ( plates can be found in the B2-SBRAC carton )
2. Mataki na 2
   • Shigar da madaidaicin allo (B2-SBRAC) zuwa Shush30 Extrusion tare da pcs 8 M5x6 sukurori.
3. Mataki na 3
   • Gyara ɓangarorin allo (B2-SBRAC) zuwa firam ɗin tebur tare da pcs 10 M6x10 sukurori.

EPS (900mm H Eco Panel) Shigar da allon allo

1. Mataki na 1
   • Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10 Screws
   • The direction as the photos display.
2. Mataki na 2
   • Sanya kwamitin EPS akan maƙallan allo
   • Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
   • Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.

Tambayoyin da ake yawan yi

How many table feet are included in the package?

There are two table feet included.

What size screws are used for fixing the lifting column?

You need to use 4pcs of screws M6x12 for fixing the lifting column.

How many pcs of Allen Wrench are provided?

There is one Allen Wrench of 4mm and one Allen Wrench of 5mm provided in the package.

Takardu / Albarkatu

Ƙarfafa B2-SSCT Tsayayyen Frame Guda [pdf] Jagoran Jagora B2-SSCT, B2-SSARM, B2-SBRAC, B2-SSCT Tsayayyen Frame Guda, B2-SSCT, Tsayayyen Firam guda ɗaya, Firam ɗaya, Firam

Magana

• Manual mai amfani