Tsarin shigarwa

Koyaushe cire haɗin wutar lantarki kafin sakawa ko maye gurbin kwan fitila da kafin tsaftacewa ko wasu kulawa.

1. Cire kayan aiki daga ainihin fakitin sa.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. Don canza tsayin tsayin daka, turawa ka riƙe gripper waya (2g), zamewar waya zuwa tsayin da ake so sannan a saki gripper na waya (2g) don amintaccen (Cire igiyar waya idan ya cancanta)
5. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1e)
6. Yi hanyoyin haɗin lantarki da suka dace (baƙi zuwa zafi “L”, fari zuwa tsaka tsaki “N”, ƙasa zuwa “GND”) tare da ƙwayayen waya (1b) da aka tanadar a cikin kunshin hardware
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. Tsawon waya mai kyau idan ya cancanta, ta hanyar turawa da riƙe igiyar waya (2g) sannan daidaita waya zuwa tsayin da ake so.

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: tura

LED Wireless kula da nesa umarnin aiki

I. Key function of remote control

1. haske mai nuna alama
2. Kunna
3. haske +
4. sanyi haske
5. sake zagayowar
6. Kashe
7. haske -
8. dumi haske
9. hasken dare

II. Key instructions

Kunna: ɗan gajeren lokaci lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

Kashe: ɗan gajeren lokaci lamp goes out, Electricity within 5s, Long press for clear code function, After power on 5 s, Long press has no effect;

Hasken sanyi +:

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Haske mai dumi +:

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp yana duhun matakin ɗaya, Akwai matakan 15 na hasken dumi daga waje zuwa cikakken haske;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, Akwai matakan haske 11 daga mafi girma zuwa mafi ƙasƙanci;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: Short danna maɓallin hasken dare, Mafi ƙarancin haske na alamp converted to Warm light;

The key light : Key indicator light, The indicator button is pressed;

Lura: Ɗaya daga cikin Saitunan Hasken dumama da sanyaya, Abokan ciniki na iya ayyana kansu bisa ga wutar lantarki da lamps.

III. Functional specifications

Aikin taswira

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 seconds. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. But a remote control can be coded and controlled with multiple LED lights,

Aikin share lamba

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 seconds, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Note: The function of code clearing is based on the code matching between the remote control and the lamp, Domin misaliample, a cikin wadannan lokuta, da ramut da kuma lamp do not have the function of code clearing, If there is no clear code function, A long press to turn off the light has no effect.
(1) The remote control is not coded with the lamp, Then there is no clear code function.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

Lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Kashe aikin ƙwaƙwalwar ajiya

Yi amfani da ramut don daidaita hasken fitilun LED, Hasken LED lamps kuma za a adana lambar ƙimar na'ura mai nisa a cikin ƙwaƙwalwar ajiyar mai sarrafa LED bayan 15S na wutar lantarki, kunna wuta bayan kun rasa iko kuma kunna lamp at its previous brightness, And has the code remote control is still controllable.

Takardu / Albarkatu

Digilog E27 LED Wutar Lantarki Mai Nisa mara waya [pdf] Jagoran Shigarwa E27 LED Wutar Lantarki mai nisa mara waya, E27, Hasken Hasken Wutar Lantarki mara waya ta LED, Hasken Wuta Mai Nisa, Gyaran Haske, Tsayawa

Magana

• Manual mai amfani