ED-PAC3020 EDATEC Masana'antu Automation da Sarrafa

Ƙayyadaddun bayanai

• Sunan samfur: Saukewa: ED-PAC3020
• Mai ƙira: EDA Technology Co., Ltd
• Ranar Saki: Agusta 1, 2025
• Software na Shirye-shirye: CODESYS V3.5 SP19
• Saitunan Ƙwaƙwalwar Ƙwaƙwalwa: 2GB DDR + 128GB SSD or 8GB DDR + 256GB SSD
• Hanyoyin sadarwa: HDMI, USB, Ethernet, RS232, RS485

Umarnin Amfani da samfur

1. Ƙarsheview:
   1. The ED-PAC3020 is a real-time CODESYS programmable automation controller suitable for industrial control and IoT fields. It comes pre-installed with a multi-core CODESYS runtime and offers different memory configurations based on user requirements.
2. Hardware:
   1. The device features commonly used interfaces such as HDMI, USB, Ethernet, RS232, and RS485. It integrates an RTC and supports connection to remote EtherCAT-based I/O modules.
3. Introduction to CODESYS Software:
   1. The product supports CODESYS V3.5 SP19 and later versions for programming and control.
4. Aikace-aikacen Sadarwar Sadarwa:
   1. The device offers EtherCAT, Ethernet, RS485, and RS232 interfaces for multi-layer network communication to meet diverse application requirements.

Panel na gaba:

1. RS232 tashar jiragen ruwa: Ana amfani da shi don haɗa kayan sarrafawa na ɓangare na uku.
2. Green UART indicators: Check the communication status of UART port.
3. Alamar wutar ja: Yana nuna matsayin ƙarfin na'urar.
4. Green system status indicator: Shows system read/write operations status.
5. Audio Output (HPO): Fitowar sauti na sitiriyo.
6. Input Audio (LINE IN): Yana goyan bayan shigar da sautin sitiriyo.
7. RS-485 port: Used to connect third-party control equipment.
8. USB 2.0 tashar jiragen ruwa: Yana goyan bayan adadin watsawa har zuwa 480Mbps.

Manufofin Hardware

• Wannan babin yana gabatar da samfurin gaba ɗayaview, CODESYS software, aikace-aikacen sadarwar, lissafin marufi, bayyanar, maɓalli, masu nuna alama da musaya.

Ƙarsheview

• The ED-PAC3020 is a real-time CODESYS programmable automation controller, pre-installed by default with a multi-core CODESYS runtime. Depending on the application scenario and user requirements, it offers programmable logic system configurations with either 2GB DDR + 128GB SSD or 8GB DDR + 256GB SSD.

GARGADI

• The ED-PAC3020 device comes pre-installed with a valid CODESYS license by default. Reinstalling the operating system will invalidate the CODESYS license. Do not attempt to install the OS on your own.
• ED-PAC3020 yana ba da musaya da aka saba amfani da su kamar HDMI, USB, Ethernet, RS232, da RS485, yana haɗa RTC, kuma ana amfani dashi da farko a cikin sarrafa masana'antu da filayen IoT.
• The ED-PAC3020 supports connection to remote EtherCAT-based I/O modules (e.g., couplers, DI, DO, AI, AO) via an EtherCAT network.
• The device integrates the CODESYS Control Runtime System, supporting IEC 61131-3 programming standards and industrial communication protocols like EtherCAT and Modbus TCP.

Users can optionally enable additional functionalities by licensing features such as:

• TargetVisu
• WebVisu Softmotion
• CNC + Robotics
• Babban darajar EtherCAT
• Modbus TCP Master
• OPC UA Server

Ana samun saiti na al'ada don saduwa da takamaiman buƙatun aikace-aikacen.

Introduction to CODESYS Software

• CODESYS (Controller Development System) is an open industrial automation software development platform that provides a full-stack solution for programming, debugging, and maintaining programmable logic controllers (PLCs), industrial PCs (IPCs), and embedded control systems.
• Compliant with the IEC 61131-3 international standard, it supports complex logic control, multi-axis motion control, industrial communication protocol integration, and real-time data processing.
• It is widely used in smart manufacturing, energy management, logistics automation, and other industrial fields.

Mabuɗin Abubuwan CODESYS:

• Standardized Programming Language Support
  • Full compatibility with the IEC 61131-3 programming languages:
    • Tsani Tsani (LD)
    • Tsarin Toshe Aiki (FBD)
    • Rubutun Tsari (ST)
    • Jerin umarni (IL)
    • Jadawalin Ayyukan Jeri (SFC)
  • Supports Object-Oriented Programming (OOP) extensions for large-scale complex projects.
• Cross-Platform Development & Deployment
  • Development Environment: Compatible with Windows and Linux operating systems, offering a unified engineering interface.
  • Target Systems: Deployable on 2,000+ industrial controller hardware platforms, including ARM/X86 architectures.
• Modular Engineering Libraries
  • Prebuilt Libraries: Include industrial protocol stacks (Modbus/TCP, OPC UA, EtherCAT) and advanced control modules (PID control, CNC interpolation algorithms).
  • Custom Libraries: Support encapsulation and reuse of Function Blocks and POUs (Program Organization Units).
• Visual Debugging & Diagnostic Tools
  •  Real-time monitoring of variables, I/O mapping, and task execution status with waveform analysis.
  • Advanced debugging tools: breakpoints, step-by-step execution, and cross-referencing for rapid fault diagnosis.
  • Integrated HMI development tools for seamless SCADA system integration.
• ED-PAC3020 tana goyan bayan CODESYS V3.5 SP19 da sigar baya.

Aikace-aikacen Sadarwar Sadarwa

• The ED-PAC3020 features EtherCAT, Ethernet, RS-485 and RS-232 interfaces, enabling multi-layer network communication to meet diverse application requirements across various scenarios. A typical application topology is illustrated in the figure below:

Jerin Shiryawa

• 1 x ED-PAC3020 Unit
• 4 x Pads

Bayyanar

• Introducing the functions and definitions of the interfaces on each panel.

Kwamitin Gaba

Gabatar da gaban panel dubawa iri da ma'ana.

A'A.	Aiki Ma'anarsa
	1 x RS232 port, 3-Pin 3.5mm pitch phoenix terminal, which is used to connect the third-party control kayan aiki.
2	2 x kore UART Manuniya, wanda ake amfani da su duba sadarwa matsayi na UART tashar jiragen ruwa.
3	1 x alamar wuta ja, wanda ake amfani da shi don duba matsayin kunnawa da kashe wutar lantarki.
4	1 x alamar yanayin tsarin kore, wanda ake amfani dashi don view matsayin tsarin karanta / rubuta ayyukan.
5	1 x Audio Output (HPO), 3.5mm jack jack audio (kore), fitarwa audio sitiriyo.
6	1 x Audio Input (LINE IN), 3.5mm jack jack audio (ja), mai goyan bayan shigar da sautin sitiriyo.
7	1 x RS485 tashar jiragen ruwa, 3-Pin 3.5mm filin jirgin ruwa na Phoenix, wanda ake amfani dashi don haɗa kayan sarrafawa na ɓangare na uku.
8	2 x USB 2.0 tashar jiragen ruwa, Mai haɗa nau'in-A, kowane tashoshi yana goyan bayan ƙimar watsawa har zuwa 480Mbps.
9	2 x USB 3.0 tashar jiragen ruwa, Mai haɗa nau'in-A, kowane tashoshi yana goyan bayan ƙimar watsawa har zuwa 5Gbps.
10	1 x Ethernet interface (10/100/1000M auto-negotiation), RJ45 connector, EtherCAT communication interface for connecting to EtherCAT networks, with PoE (Power over Ethernet) support.

Rear Panel

• Gabatar da rear panel interface iri da ma'anoni.

A'A.	Aiki Ma'anarsa
1	1 x maɓallin wuta, wanda ake amfani dashi don kunnawa da kashe na'urar.
2	1 x Micro SD Ramin katin, an tanada don amfani na gaba. Lura: Na'urar tana yin takalma daga SSD ta tsohuwa. An tanada wannan Ramin katin Micro SD don yuwuwar fadada.

Bangaren gefe

• Gabatar da nau'ikan mu'amalar panel panel da ma'anoni.

A'A.	Aiki Ma'anarsa
1	shigarwar 1 x DC, mai haɗin USB Type-C, wanda ke goyan bayan shigarwar wutar lantarki 5V 5A.
2	2 x HDMI tashar jiragen ruwa, Mai haɗa Micro HDMI, wanda zai iya haɗa nuni kuma yana goyan bayan 4K 60Hz

Maɓalli

• The ED-PAC3020 includes a ON/OFF button, and the silkscreen is “ON/OFF”. If you run Raspberry Pi Desktop, you can initiate a clean shutdown by briefly pressing the power button. A menu will appear asking whether you want to shutdown, reboot, or logout.

TIP

• Idan kuna gudanar da Rasberi Pi Desktop, zaku iya danna maɓallin wuta sau biyu a jere don rufewa.

Mai nuna alama

• Wannan sashe yana bayanin matsayi da ma'anoni masu nuni da aka haɗa cikin na'urar ED-PAC3020.

​Indicator	Matsayi	Bayani
PWR	On	An kunna na'urar.
	Kifta ido	Power supply of the device is abnormal, please stop the power supply immediately.
	Kashe	Ba a kunna na'urar ba.
ACT	Kifta ido	The system started successfully and is reading and writing data.

​Indicator	Matsayi	Bayani
	Kashe	The device is not powered on or does not read and write data.
COM1 ~ COM2	Kunna/Kifta ido	Ana watsa bayanai
	Kashe	The device is not powered on or there is no data transmission.
Yellow indicator of Ethernet port	On	Haɗin Ethernet yana cikin yanayin al'ada.
	Kifta ido	The Ethernet connection is abnormal.
	Kashe	Ba a saita haɗin Ethernet ba.
Green indicator of Ethernet port	On	Haɗin Ethernet yana cikin yanayin al'ada.
	Kifta ido	Ana watsa bayanai ta hanyar tashar Ethernet.
	Kashe	Ba a saita haɗin Ethernet ba.

TIP

• An canza aikin alamar PWR/ACT akan Rasberi Pi 5 zuwa keɓantattun alamun PWR da ACT ta tsohuwa, don haka alamar PWR/ACT ta kasance a kunne bayan an kunna na'urar.

Interface

• Gabatar da ma'ana da aikin kowane mai dubawa a cikin samfurin.

Interarfin wutar lantarki

• Na'urar ED-PAC3020 ta ƙunshi haɗin shigar da wutar lantarki guda ɗaya, wanda ke amfani da haɗin USB Type-C mai lakabin "PWR IN" kuma yana goyan bayan shigarwar wutar lantarki na 5V 5A.

TIP

• In order for Raspberry Pi 5 to achieve better performance, it is recommended to use a 5V 5A power adapter.
• 1.8.2 1000M Ethernet Interface (EtherCAT)
• The ED-PAC3020 device includes one auto-negotiating 10/100/1000M Ethernet interface with an RJ45 connector featuring status LEDs, labeled as ” “. This interface serves as an EtherCAT communication port for connecting to EtherCAT networks and supports PoE (Power over Ethernet) power delivery.

Hanyar Hanya ta HDMI

• Na'urar ED-PAC3020 ta haɗa da 2 HDMI musaya ta amfani da masu haɗin Micro HDMI, mai lakabi "HDMI", don haɗa nunin HDMI. Waɗannan musaya suna tallafawa fitowar bidiyo har zuwa 4Kp60.

TIP

• Some third-party Micro HDMI cables may have shorter Micro HDMI connectors, which could cause connection issues. It is recommended to use the official Raspberry Pi Micro HDMI to Standard HDMI cable for optimal compatibility.

USB 2.0 Interface

• The ED-PAC3020 device includes 2 USB 2.0 interfaces with standard Type-A connectors, labeled as ““. These interfaces support connecting standard USB 2.0 peripherals and offer a maximum transfer rate of 480Mbps.

USB 3.0 Interface

• The ED-PAC3020 device includes 2 USB 3.0 interfaces with standard Type-A connectors, labeled as “ “. These interfaces support connecting standard USB 3.0 peripherals and offer a maximum transfer rate of 5Gbps.

Bayanan Bayani na RS232

• The ED-PAC3020 device includes 1 RS232 interface with a 3-Pin 3.5mm pitch Phoenix terminal, labeled “TX/RX/GND”.

Ma'anar Pin

• Terminal pins are defined as follows:

	Pin ​ID	Sunan Pin
	1	TX
	2	RX
	3	GND

Ƙaddamarwar RS232 ta dace da sunayen fil masu zuwa akan Pi5:

Sigina	Pi5 GP​IO Name	Pi5 Pin Fita
TX	Farashin GPIO4	UART3_TXD
RX	Farashin GPIO5	UART3_RXD

Tsarin wiring na RS232 shine kamar haka:

Bayanan Bayani na RS485

• The ED-PAC3020 device includes 1 RS485 interface with a 3-Pin 3.5mm pitch Phoenix terminal, labeled “A/B/GND”.

Ma'anar Pin

• Terminal pins are defined as follows:

	Pin ​ID	Sunan Pin
	1	A
	2	B
	3	GND

Ƙaddamarwar RS485 ta dace da sunayen fil masu zuwa akan Pi5:

Sigina	Pi5 GP​IO Name	Pi5 Pin Fita
A	Farashin GPIO12	UART5_TXD
B	Farashin GPIO13	UART5_RXD

Haɗin igiyoyi

• Tsarin wiring na RS485 shine kamar haka:

RS485 Yana Kashe Kanfigareshan Resistor

• The ED-PAC3020 device includes 1 RS485 interface.
• A 120Ω termination resistor is reserved between the A and B lines of the RS485 circuit. Inserting a jumper cap enables this termination resistor.
• By default, no jumper is installed, rendering the 120Ω termination resistor inactive. The termination resistor is located at J7 on the PCBA (printed circuit board assembly).

TIP

• The device case must be opened to inspect the 120Ω termination resistor.

Shigar Audio

• Na'urar ED-PAC3020 ta ƙunshi haɗin shigar da sauti na 1 (LINE IN), jack jack 3.5mm mai jiwuwa, mai lakabin "", wanda ke goyan bayan shigarwar sitiriyo.

Fitar Audio

• The ED-PAC3020 device includes 1 audio output interface (HPO), a green 3.5mm audio jack, labeled as ” “, which supports stereo output.

Shigar da Na'urar

• An tsara na'urar ED-PAC3020 don sanya tebur ta tsohuwa kuma tana goyan bayan hawan bango tare da madaidaicin bangon bangon ED-ACCBKT-L3020 daga kamfaninmu.

TIP

• The ED-PAC3020 packaging box does not include the ED-ACCBKT-L3020 by default. Users must purchase it separately.

Shiri:

• Prepared a Phillips-head screwdriver.
• Obtained the ED-ACCBKT-L3020 wall-mount bracket.

Mataki:

1. Use a Phillips screwdriver to unscrew the four M2.5 screws on the side of the ED-IPC3020 counterclockwise.
2. Align the left and right brackets of the ED-ACCBKT-L3020 with the screw holes on both sides of the ED-PAC3020, insert the four M2.5*6 screws, and tighten them clockwise with a Phillips screwdriver to secure the ED-ACCBKT-L3020 to the sides of the ED-PAC3020.
3. Based on the spacing and diameter of the wall-mounting screw holes of the ED-ACCBKT-L3020 left and right brackets (refer to the diagram below), drill holes in the wall accordingly, then proceed with wall-mounted installation of the device.
   Naúrar: mm
4. Tolerance: 0.5-6±0.05, 6-30±0.1, 30-120±0.15

Girma

Buga Na'urar

• Wannan babin yayi cikakken bayani kan takamaiman hanyoyin haɗa igiyoyi da kunna wuta akan na'urar.

Haɗin igiyoyi

• This section describes the procedures for connecting cables to the device.

Shiri:

• Obtained fully functional accessories such as a switch, monitor, mouse, keyboard, I/O expansion module, and power adapter.
• Available functional network connection.
• Available functional cables: HDMI cable and Ethernet cable.

Tsarin tsari na igiyoyi masu haɗawa:

• Please refer to 1.8 Interface for the pin definition of each interface and the specific method of wiring.

TIP

• Some third-party Micro HDMI cables may have shorter Micro HDMI connectors, which could cause connection issues. It is recommended to use the official Raspberry Pi Micro HDMI to Standard HDMI cable for optimal compatibility.

Booting The System For The First Time

• Once the ED-PAC3020 is connected to power, the system will begin to boot up.
• Red PWR indicator: Lights up to indicate the device is receiving power.
• Green ACT indicator: Blinks to signal normal system startup. The Raspberry Pi logo will then appear in the upper-left corner of the screen.

TIP

• The default username is pi, the default password is raspberry.

Rasberi Pi OS (Desktop)

• Idan na'urar ta kasance masana'anta ne tare da Desktop OS, za ta yi taɗa kai tsaye zuwa cikin mahallin tebur yayin farawa, kamar yadda aka nuna a hoton da ke ƙasa.

Rasberi Pi OS (Lite)

• Idan na'urar an shigar da masana'anta tare da Lite OS, za ta shiga ta atomatik ta amfani da tsoffin takaddun shaida bayan farawa. Hoton da ke ƙasa yana nuna cewa tsarin ya tashi cikin nasara.

CODESYS Programming

• Wannan babin yana ba da cikakken bayani kan takamaiman ayyukan da ke tattare da amfani da CODESYS.

GARGADI

• The ED-PAC3020 device comes pre-installed with a valid CODESYS license by default. Reinstalling the operating system will invalidate the CODESYS license. Do not attempt to install the OS on your own.
• CODESYS Software Download and Installation

TIP

• The installed CODESYS IDE version must be 3.5.19 or higher, and the PC operating system must be Windows 10 or Windows 11 (64-bit recommended).
• Download the installation package from the official CODESYS website. Zazzagewar URL is https://store.codesys.com/de/ (https://store.codesys.com/de/).
• TIP
• When downloading from the CODESYS official webshafin a karon farko, dole ne ka fara rajista kuma ka shiga cikin asusunka.
• Right-click the downloaded installer and select “Run as administrator” from the context menu. Click “Install” in the opened installation interface, and keep the default configuration during the installation process.
• After the installation is complete, click “Finish” to close the installation interface.

Obtaining and Installing Device Description File

• Kafin haɗi zuwa na'urar ta CODESYS, kuna buƙatar saukewa kuma shigar da bayanin na'urar file na farko.

Obtaining Device Description File

TIP

• The device’s default Ethernet port IP address is 192.168.0.100. To modify it, refer to Configuring Ethernet IP.

Shiri:

• A CODESYS-authorized ED-PAC3020 is available.
• A functional Ethernet cable is available.
• A Windows PC is prepared, with its IP address configured to the same subnet as the device. For example, idan IP na na'urar (1000M Ethernet tashar jiragen ruwa) shine 192.168.0.100 , saita IP na PC zuwa 192.168.0.99 .

Matakai:

1. Connect the device’s Ethernet port to the PC via an Ethernet cable, then power on the device.
2. Enter http://192.168.0.100:8100 in the PC’s web browser don samun dama ga "PLC Setting" interface.
3. In the “Device Info” section, click the “[Download] Device Description File” button to download the corresponding “.xml” format device description file.

TIP

• Also available directly in the document ED-PAC3020 Device File (https://vip.123pan.cn/ 1826505135/17964309) .

Installing Device Description File

Shiri:

• A PC installed with CODESYS software version V3.5 SP19 (64-bit).
• An ED-PAC3020 device with a valid CODESYS license and its corresponding device description file.
• Connect both the PC and ED-PAC3020 to the network, ensuring their IP addresses are within the same subnet.

Matakai:

• Double-click the CODESYS icon on the PC desktop to open the CODESYS software. From the menu bar, select “Tools” → “Device Repository”.
• In the opened “Device Repository” pane, click “Install”.
• In the pop-up “Install Device Description” pane, select the device description file da za a shigar da kuma danna "Bude" don ci gaba da shigarwa.
• After successful installation, you can verify in the “Device Repository” that the device description file an kara nasara cikin nasara.

Installing Remote I/O Device Description File

Shiri:

• A PC installed with CODESYS software version V3.5 SP19 (64-bit).
• An ED-PAC3020 device with a valid CODESYS license.
• The remote I/O device description files an sauke su daga: Bayanin I/O mai nisa Files (https://vip.123pan.cn/1826505135/16632390).
• Connect the PC, ED-PAC3020, and remote I/O devices to the same switch. Ensure that the IP addresses of the PC, ED-PAC3020, and remote I/O devices are within the same subnet.

Matakai:

1. Double-click the CODESYS icon on the PC desktop to open the CODESYS software. From the menu bar, select “Tools” → “Device Repository”.
2. In the opened “Device Repository” pane, click “Install”.
3. In the pop-up “Install Device Description” pane, select the I/O device decirption file da za a shigar da kuma danna "Bude" don ci gaba da shigarwa.
4. After successful installation, you can verify in the “Device Repository” that the I/O device description file an kara nasara cikin nasara.

Kanfigareshan Hardware

Shiri:

• A PC installed with CODESYS software version V3.5 SP19 (64-bit).
  • Bayanin na'urar files da bayanin na'urar I/O mai nisa files have been installed. Connect the PC, ED-PAC3020, and remote I/O devices to the same switch. Ensure that the IP addresses of the PC, ED-PAC3020, and remote I/O devices are within the same subnet.

Create a New Project and Connect to the Device

Matakai:

• Power on the ED-PAC3020 and the remote I/O modules. Open the CODESYS software on the PC, select “File” → “New Project” in the menu bar to open the “New Project” pane, and create a standard project.
• Select the installed device description file kuma danna "Ok".
• Double-click the device, select “Scan Network” on the right, then choose the detected device from the scan results, and click “OK” to confirm.

TIP

• If the device cannot be detected during scanning, manually enter the IP address in the target device settings to connect.
• If a device login prompt appears, log in with your credentials (username and password) or follow the instructions to register a new account.\

As shown in the figure below, this indicates the device is successfully connected.

Adding Remote I/O Modules

Matakai:

1. Right-click “Device” and select “Add Device” in the menu to add the EtherCAT Master.
2. Double-click on the EtherCAT Master device to set the source address (Select the EtherCAT port, which corresponds to the device’s eth0 port).
3. Danna button to log in to the device. A successful login is shown in the figure below.
4. Click on the EtherCAT Master device, select “Scan for Devices” in the right-click menu, and copy all devices to the project after scanning is completed.
5. Danna button to log out of the device.
6. Double-click the slave device, configure the relevant parameters in the right-hand interface, enable “Expert settings”, select “Enable” under Select DC section, and select “Enable Sync0”.
7. Danna button to download the program to the device, then click the  button to run it. As shown in the figure below, this indicates a successful operation.

Shirye-shirye

• Mai zuwa example yana nuna shirye-shirye masu amfani ta amfani da takamaiman yanayin coding.

Tsarin Shirye-shiryen

Shirye-shiryen Example

• Complete the development and debugging of a program for a timed blinking LED using a PNP-type 8-channel digital output (DO) module.

Shiri:

• A standard project has been created.
• Hardware configuration has been completed.
• A 24V compact LED lamp has been connected to the first output port of the remote DO (Digital Output) module.

Matakai

• Double-click the DO module, select “Module I/O Mapping” → “Output” in the right-hand interface, and view adiresoshin duk tashar jiragen ruwa masu fitarwa. Kamar yadda aka kwatanta a ƙasa, adireshin tashar fitarwa ta farko shine %QX18.0 .
• Write the program code as follows:
• After completing the program, click ” ” to compile it and ensure there are no errors.
• Click Login to download the program to the device, then click Run to observe the LED blinking every 0.5 seconds.

Aiki da Kulawa

• Bayan saukar da shirin zuwa na'urar, zaku iya aiwatar da ayyukan Run da Tsaida.

Matsayi	Ayyuka
Run Shirin	In the main menu of the software interface, click the Login  button.
Tsaida Shirin	In the main menu of the software interface, click the stop  button.

Tsarin Tsara

• Wannan babin yana gabatar da yadda ake saita tsarin.

GARGADI

• The ED-PAC3020 device comes pre-installed with a valid CODESYS license by default. Reinstalling the operating system will invalidate the CODESYS license. Do not attempt to install the OS on your own.
• Neman Na'urar IP
  • Neman Na'urar IP
• M Login
  • M Login
• Ana saita Wi-Fi
  • Ana saita Wi-Fi
• Saita Ethernet IP
  • Saita Ethernet IP
• Configuring Bluetooth.
  • Yana daidaita Bluetooth
• Ana saita Buzzer
• The buzzer is controlled using GPIO6.
• Execute the following command to turn on the buzzer:
• Ana saita RTC
  • Ana saita RTC
• Ana saita Serial Port
• Wannan babin yana gabatar da hanyar daidaitawa na RS232 da RS485.

Installing Picocom Tool

• In the Linux environment, you can use the picocom tool to debug the serial ports RS232 and RS485.
• Execute the following command to install the picocom tool.
• 5.8.2 Yana saita RS232
  ED-PAC3020 yana ƙunshe da ƙirar 1 RS232, da tashar tashar COM da na'urar ta daidai. files an jera su a cikin tebur da ke ƙasa:

Lamba of Saukewa: RS485 Tashoshi	Daidaitawa COM Port	Daidaitawa Na'ura File
1	COM2	/dev/com2

• Input commands as needed to control external device.

Configuring RS485

• The ED-PAC3020 contains 1 RS-485 interface, and its corresponding COM port and device files an jera su a cikin tebur da ke ƙasa:

Lamba of Saukewa: RS485 Tashoshi	Daidaitawa COM Port	Daidaitawa Na'ura File
1	COM2	/dev/com2

Shiri:

The RS485 ports of ED-PAC3020 has been connected with external device. Steps:

1. Execute the following command to open the serial port com2, and configure the serial port baud rate to 115200.
2. Input commands as needed to control external device.

Yana daidaita Sauti

• Yana daidaita Sauti
• CODESYS License Management
• Na'urar ED-PAC3020 ta zo an riga an shigar da ita tare da lasisin CODESYS ta tsohuwa. Kuna iya yin ajiya da mayar da lasisin ta hanyar samun damar dubawar "PLC Setting".

License Backup
Shiri:

• A Windows PC has been set up with an IP address in the same subnet as the device. For example, idan IP na na'urar (1000M Ethernet tashar jiragen ruwa) shine 192.168.0.100 , saita IP na PC zuwa 192.168.0.99 .
• A functioning Ethernet cable has been prepared.

Matakai:

• Connect the device’s 1000M Ethernet port to the PC via an Ethernet cable, then power on the device.
• Enter http://192.168.0.100:8100 in the PC’s web browser don samun dama ga "PLC Setting" interface.
• In the “Codesys License Management” interface, click “Backup License” to download the license file kuma ajiye shi a gida.

TIP

• The backed-up license file za'a iya dawo dasu akan na'urar guda kawai.

License Restore

Shiri:

• A Windows PC has been set up with an IP address in the same subnet as the device. For example, idan IP na na'urar (1000M Ethernet tashar jiragen ruwa) shine 192.168.0.100 , saita IP na PC zuwa 192.168.0.99 .
• A functioning Ethernet cable has been prepared.
• The backed-up license file an samu.

Matakai

1. Connect the device’s 1000M Ethernet port to the PC via an Ethernet cable, then power on the device.
2. Enter http://192.168.0.100:8100 in the PC’s web browser don samun dama ga "PLC Setting" interface.
3. In the “Codesys License Management” interface, click “Restore License”.
4. As prompted, select the obtained license file under a custom path.
5. After a successful License Restore, a 100% progress bar will be displayed in the right-hand panel.
6. Open the device’s terminal command pane, execute the following command, and restart the device.

Tambayoyin da ake yawan yi

Tambaya: Zan iya sake shigar da tsarin aiki akan ED-PAC3020?

A: Reinstalling the operating system will invalidate the CODESYS license that comes pre-installed by default. It is advised not to attempt installing the OS on your own.

Tambaya: Wadanne matakan shirye-shirye ne ED-PAC3020 ke tallafawa?

A: The device supports IEC 61131-3 programming standards and industrial communication protocols like EtherCAT and Modbus TCP.

Takardu / Albarkatu

EDA ED-PAC3020 EDATEC Masana'antu Automation da Sarrafa [pdf] Manual mai amfani ED-PAC3020 EDATEC Kayan Aiki da Gudanarwa na Masana'antu, ED-PAC3020, EDATEC Automation Automation da Sarrafa, Masana'antu Automation da Sarrafa, Aiki da sarrafawa

Magana

• Manual mai amfani