The HyperCube features 3 modes: Kaleidoscopic, Meditative, and
Sound Reactive.
Each mode has unique patterns that can be controlled using the
button on the control box.
The Hyperspace App allows for full customization and control of
the HyperCube.

The Button:

Hold (2s): Turn off
Hold (10s): Reset WiFi credentials

The Hyperspace App:

Hyperspace Lighting

Download the app for complete control and customization of your
HyperCube.

Ensure the cube is not in sound reactive mode.
Open the app, add a new Hyper-Device, enter WiFi credentials,
da haɗi.

Tambayoyin da ake yawan yi (FAQ):

Q: Can I leave the HyperCube on for extended periods?

A: It is recommended to turn off the HyperCube when not in use
to conserve energy and prolong the lifespan of the LEDs.

Q: How do I clean the HyperCube mirrors?

A: Use a microfiber cloth with light soapy water to gently clean
the mirror panels. Avoid applying excessive pressure to prevent
lalacewa.

View Fullscreen

HyperCube
SE
Littafin mai amfani
DOn’t Panic!
This is your personal guide to your new hyperdimensional portal device

Teburin Abubuwan Ciki
Table of Contents……………………………………………………………2 Safety and Care ………………………………………………………………2 Getting Started ……………………………………………………………….4
What’s in the box?!………………………………………………………4 Powering up ……………………………………………………………….4 Operation ……………………………………………………………………….5 The Button………………………………………………………………….6 The Hyperspace App……………………………………………………….7 Setup …………………………………………………………………………7 Usage …………………………………………………………………….. 13 Troubleshooting ………………………………………………………….. 19 Warranty …………………………………………………………………….. 20 Contact ………………………………………………………………………. 20 Tech Specs …………………………………………………………………. 21
German/Deutsch……………………………………………………………………. 22 French/Français…………………………………………………………………….. 41 Dutch/Nederlands………………………………………………………………….. 60
2

Lafiya da Kulawa
WARNING Fire Hazard
Keep the HyperCube out of direct sunlight. In rare cases, the mirrors can focus sunlight into a point that could cause burns or risk of fire.
WARNING Keep Dry
Keep the HyperCube, and its controller and power supply away from excessive moisture. Water can damage the electronics and cause LED malfunction. Prolonged exposure can lower the lifetime of the LEDs. Our warranty does not cover water damage.
WARNING Electric Shock Risk
Do not use or operate the device when wet for risk of electric shock.
Hyper-Care
The HyperCube is an art piece; while it is sturdy, it is not meant to be handled excessively. Be extremely careful with the mirrors. When cleaning the mirror panels, use only a microfiber cloth and, if needed, lightly soapy water. Clean very gently, without applying much pressure, to prevent damage to the mirrored panels.
CE Registration: HK2506203256E
3

Farawa
What’s in the box?!
HyperCube Control Box Power Supply
Ƙarfafawa
1. Plug the power supply into an outlet (accepts outlet voltage from 100-240V) and plug the USB cord into the power supply. You may also use any standard cell phone charging block (5V) with your own USB-C cord.
2. Connect the HyperCube cable to the control box. Note the orientation. To unplug, press the tab underneath.
4

3. Plug the USB-C connector into the front of the control box. The button on the control box will turn blue.
4. Let there be light!
Aiki
The HyperCube features 3 modes: Kaleidoscopic: dynamic, fast, and colorful patterns. This is the default mode (40 patterns) Meditative: calm, classy and slowed down patterns to help you relax (24 patterns) Sound Reactive: dance and entrance, with specially designed patterns that respond to the beat. A microphone is located inside the control box (31 patterns)
5

Each mode is essentially a playlist of unique patterns. By default, a pattern plays for 60 seconds before switching. New colors are randomly generated every 10 seconds, for nearinfinite variety! This behavior can be fully customized in the app. The patterns and modes can be controlled with the button on the control box.

Maballin
× 1: Next pattern × 2: Change mode:
Kaleidoscopic Meditative Sound Reactive

Hold (2s): Turn off
Hold (10s): Reset WiFi credentials

The Hyperspace App
Hyperspace Lighting
Download the “Hyperspace Lighting” app to fully control and customize your HyperCube!
Saita
The setup process will connect your HyperCube to your home WiFi network for convenient smartphone control.
(NOTE: the HyperCube only connects to 2.4 GHz networks)
1. Make sure the cube is not in sound reactive mode.
2. Open the app and press the “+” icon in the top right corner of the main menu
7

3. Press “Add New Hyper-Device”

4. Enter your home WiFi credentials and press “Connect!”. All fields are case sensitive. Your phone must be connected to this network

Note: if the connection fails, press “Can’t Connect?” at the bottom of the screen and follow the instructions.
8

5. Accept any permissions and allow your phone to connect to the HyperCube WiFi network channel
6. Wait for the connection process to finish. This could take up to one minute
7. You may go back at any time to re-enter your WiFi credentials or restart the process. Multiple attempts may help in case of failure
8. You’re done – press “My HyperCube” to pilot the controls!
9

Matsalar haɗuwa?
9. Refresh: If the connection process finished but the cube isn’t showing up, refresh the device list by swiping down anywhere on the screen
10. Power the cube off and on (fully unplug), then reset the cube’s WiFi by holding the button on the control box for 10s (until the LEDs in the cube flash red then green).
11. Repeat steps 1-7. OR, in step 4 press “Can’t Connect?” at the bottom of the screen and follow the instructions.
12. Alternatively: Press “Temporary Connect” on the “+” menu, “Config” in the top right of the device UI, then “WiFi Setup” at the top of the screen. Enter your WiFi credentials, then go back to the home screen of the app and refresh (swipe down).
Hanyoyin haɗi
· Ensure the cube is near your router for initial connection. It can be moved further after setup.
· Ensure you are connecting to a 2.4 GHz WiFi network, and your phone is already connected to this WiFi.
· Double check your WiFi name and password (both are case sensitive).
· Try again, sometimes multiple attempts are needed. Reset the cube’s WiFi and power cycle after each attempt.
10

Lost Connection?
If you’ve successfully connected before but lost connection: 1. Power cycle by fully unplugging it then plugging it back in. 2. Restart the app and refresh the device list by swiping down.
Refresh a few times and wait up to a minute. 3. If the device still does not connect, try steps 1-2 again, or reset
the device and reconnect, by following the steps on the previous page (hold the button for 10s to reset WiFi).
Not at home?
If you’re out and about without a WiFi connection, you can still connect to the HyperCube’s internal WiFi hotspot. Press the “+” icon on the main menu and select “Temporary Connect” to access the controls! This will leave you connected to the HyperCube WiFi channel.
Control via PC, without the app
If you don’t have an Android/iOS smart phone, you can still connect to and control your HyperCube! All you need is an internet browser on your PC or phone. If you have already connected the cube with your phone, simply skip to step 5.
1. On your phone, connect to the “HyperCube” WiFi network. Password: hyperspace
2. A new window will appear (or a prompt will appear asking you to log in. Press this). Enter your home WiFi network information. This procedure will connect the HyperCube to your home network.
3. Access your router settings. Typically, this can be done by entering the router IP address in a browser. Most use an address of 192.168.1.1, but you may need to confirm with your router’s manual.
11

4. Find the list of connected devices and copy the HyperCube’s IP address (also in-app, after setup).
5. Enter the HyperCube IP address in any browser and you will be taken to the controls!
Connecting via E1.31
The HyperCube also supports pixel mapping via sACN/E1.31 protocol. Various third-party software can be used to control the LEDs, such as xLights and MadMapper. This feature is experimental, not guaranteed to work smoothly, and is recommended only for users with pixel mapping experience. The setup process differs for all software. In general, you will need your
HyperCube’s IP address, shown on the main device list page:
You will also need the following pixel information: HyperCube10: 288 total pixels (WS8211/WS2812) HyperCube15: 480 total pixels (WS8211/WS2812) The total pixels are split across 2 separate LED tracks, each with half the total pixels (i.e. 2 universes with 432/840 channels each for HC10/HC15).
12

Amfani

Device List Menu

Flash LEDs to Brightness identify device slider

Juya wuta

Connect a new Hyper-Device to your home WiFi network

Swipe left to delete device from list

Swipe down to refresh device list

Note: the device list automatically refreshes every 15s. After a device has been connected, it will appear here on any phone with the Hyperspace app.

Connect directly to the cube’s WiFi

access point. This is a temporary

connection method, you will be unable

to access the internet. Use the option

above for standard at-home

haɗi.

Patterns Menu (default)

Nightlight: dims brightness over 60 minutes

Sync with other cubes

Sync brightness to music (makes any pattern sound reactive)

Toggle power

Saituna

Mode selection automatically cycle through playlist of patterns

Pattern menu

Next & previous pattern

Stay on current pattern in the mode playlist

Choose individual pattern (from any
yanayin)

Launuka Menu
Choose from predefined color palettes

Customize your own colors
Choose up to 3 unique colors

Adjust brightness of selected color
15

Daidaita haske gaba ɗaya

More Controls Menu
Adjust pattern intensity (unique effects on each pattern)

Adjust pattern speed

Symmetry menu

Pause or freeze animation

Change the symmetry of motion each pattern
nuni
16

Menu da aka fi so
Save your favorite patterns for easy playback! All color, speed, intensity, and symmetry customizations are also saved.

Don ajiyewa:
1. Press “saving mode”
2. Press a slot number to save to that slot

Don loda:
Press a highlighted slot number with a previously saved pattern

Toggle advanced settings

Menu na Saituna

Play time before pattern transition within each mode

Saitunan farawa

Random color change time
Patterns play in fixed or random order
Blend time between autotransitions Blend time between button-press transitions
18

Shirya matsala
Trouble connecting to the app?
Try the alternative connection process here.
1. Reset the cube’s WiFi by holding the button on the control box for 10s (until the LEDs in the cube flash red then green).
2. Connect to the “HyperCube” WiFi network with your phone. If prompted, stay connected without internet access.
3. Bude a web browser and navigate to hyperspace.local 4. Press “config” in the top right, then “WiFi Setup”. Enter your home
WiFi credentials (case sensitive) and save. 5. Connect back to your home WiFi, open the Hyperspace app, then
swipe down to refresh the device list. The list refreshes every 15s, you may need to wait or manually refresh multiple times. 6. Your HyperCube should now appear on the device list and be connected! 7. If all else fails, the WiFi connection can be reset by holding the button on the control box for 10 seconds. After, re-do the initial setup procedure (“+” “Add New HyperDevice Connect!).
Want to connect an additional device to the cube?
You can control one HyperCube from multiple devices. If you have already gone through the initial setup process once, on your new device simply swipe down on the main device list page to refresh. You may need to refresh multiple times, and wait up 1-2 minutes. All hyper-devices connected to the WiFi network will be added after some time.
19

Sound reactivity issues?
The HyperCube automatically adjusts to a wide range of volume levels, but still requires a moderate volume and/or distance-to-source to respond best. The microphone is located in the control box; for optimal performance, keep the sound source 3 10 ft away.
If the HyperCube appears too sensitive to ambient noise (patterns trigger with no sound) or won’t respond, the microphone sensitivity can be adjusted. Go to settings > sound reactivity and adjust the sensitivity value. Higher values will allow the mic to pick up softer sounds, but may trigger the lights on ambient/electrical noise.
Note that if music volume is extremely loud (and close to the control box), the sound response may be poor.
Garanti
The Hyperspace Lighting Company, LLC offers a 1-year limited warranty on each HyperCube. We guarantee that each product purchased will arrive in working condition, without damage, and will be free from defects in electrical operation for a period of one (1) year from the date of delivery. Please contact us at the email address below if you have any issues, we’re here to help!
The full detailed warranty description can be found online at https://hyperspacelight.com/pages/1-year-limited-warranty
Tuntuɓar
Questions, comments, concerns? Lost in hyperspace and can’t find your way out? Email us at: hello@hyperspacelight.com.
20

Bayanan Fasaha

HyperCube10-SE

Dimensions (per side) Total LEDs LEDs Per Edge Max Power Draw Avg Power Draw Weight

10.15″ (258 mm) 216 18 10W (2A) 5W (1A) 3.8 lb (1.7 kg)

HyperCube15-SE
15.16” (385 mm) 336 28 15W (3A) 7.5W (1.5A) 8.2 lb (3.7 kg)

Colors LED Rating Windows Frame Wifi Connectivity System Voltage Standby Power Draw Power Adapter Flux Capacitor Rating

~16 million 50,000+ hours Scratch-resistant mirrored acrylic
ABS 2.4 GHz
5V <1W Accepts 100 240V, 50/60 Hz 3.14 Jigawatts

CE Registration: HK2506203256E

Wannan na'urar ta bi sashe na 15 na Dokokin FCC. Aikin yana ƙarƙashin sharuɗɗa biyu masu zuwa: (1) wannan na'urar bazai haifar da tsangwama mai cutarwa ba, kuma
(2) Dole ne wannan na'urar ta karɓi duk wani tsangwama da aka karɓa, gami da tsangwama wanda zai iya haifar da aiki maras so.
Canje-canje ko gyare-gyaren da ƙungiyar da ke da alhakin bin doka ba ta amince da su ba na iya ɓata ikon mai amfani na sarrafa kayan aiki. An gwada wannan kayan aikin kuma an same shi don yin aiki da iyaka don na'urar dijital ta Class B, bisa ga Sashe na 15 na Dokokin FCC. An ƙirƙira waɗannan iyakokin don ba da kariya mai ma'ana daga tsangwama mai cutarwa a cikin shigarwar mazauni. Wannan kayan aiki yana haifar da amfani kuma yana iya haskaka ƙarfin mitar rediyo kuma, idan ba a shigar da shi ba kuma aka yi amfani da shi daidai da umarnin, na iya haifar da tsangwama mai cutarwa ga sadarwar rediyo. Duk da haka, babu tabbacin cewa tsangwama ba zai faru a cikin wani shigarwa na musamman ba. Idan wannan kayan aikin ya haifar da tsangwama mai cutarwa ga liyafar rediyo ko talabijin, wanda za'a iya tantancewa ta hanyar kashe kayan aiki da kunnawa, ana ƙarfafa mai amfani da yayi ƙoƙarin gyara tsangwama ta hanyar ɗaya ko fiye na waɗannan matakan:
- Sake daidaitawa ko ƙaura eriyar karɓa.
- Ƙara rabuwa tsakanin kayan aiki da mai karɓa.
–Haɗa kayan aiki zuwa wata maɓalli a kan wata da’ira daban-daban da wadda ake haɗa mai karɓa zuwa gare ta.
- Tuntuɓi dila ko gogaggen masanin rediyo/TV don taimako.ct.
Wannan kayan aikin ya cika FCC RF iyakokin fiddawa da aka tsara don yanayin da ba a sarrafa shi. Ya kamata a shigar da wannan kayan aikin tare da mafi ƙarancin nisa na 20cm tsakanin radiyo da kowane ɓangaren jikin ku.

Takardu / Albarkatu

HYPERCUBE HC15-SE Controller [pdf] Manual mai amfani
HC15-SE, HC15-SE Controller, Controller

Magana

Manual mai amfani

HYPERCUBE HC15-SE Controller User Manual

HC15-SE Controller

Bayanin samfur

Ƙayyadaddun bayanai:

Umarnin Amfani da samfur:

Tsaro da Kulawa:

Farawa: