Jagorar Ayyuka na M5StickC Plus2
Kamfanin Firmware
Lokacin da na'urar ta ci karo da al'amurran da suka shafi aiki, za ku iya gwada sake kunna firmware na masana'anta don bincika ko akwai matsala ta hardware. Koma zuwa koyawa mai zuwa. Yi amfani da M5Burner firmware kayan aikin walƙiya don kunna firmware na masana'anta akan na'urar.
FAQ
Q1: Me yasa M5StickC Plus2 baƙar allo/ba zai yi taya ba?
Magani: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
Q2: Me yasa lokacin aiki kawai 3 hours? Me yasa yake cajin 100% a cikin minti 1, cire kebul na caji zai kashe?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Please burn back official firmware.
Shiri
- Koma zuwa koyaswar M5Burner don kammala saukar da kayan aikin firmware mai walƙiya, sannan koma zuwa hoton da ke ƙasa don saukar da firmware ɗin daidai.
Zazzage mahaɗin: https://docs.m5stack.com/en/uiflow/m5burner/intro
Shigar da Driver USB
Tukwici na Shigar Direba
Danna mahaɗin da ke ƙasa don sauke direban da ya dace da tsarin aikin ku. Za a iya saukewa kuma shigar da kunshin direba na CP34X (na nau'in CH9102) ta zaɓar kunshin shigarwa wanda ya dace da tsarin aikin ku. Idan kun ci karo da al'amurran da suka shafi zazzagewar shirin (kamar ƙarewar lokaci ko kurakurai "An kasa rubutawa zuwa ga RAM", gwada sake shigar da direban na'urar.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS 1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Zaɓin Port akan MacOS
A kan MacOS, ana iya samun tashoshin jiragen ruwa guda biyu. Lokacin amfani da su, da fatan za a zaɓi tashar jiragen ruwa mai suna wchmodem.
Zaɓin Port
Haɗa na'urar zuwa kwamfuta ta kebul na USB. Bayan shigar direban ya cika, zaku iya zaɓar tashar na'urar da ta dace a cikin M5Burner.
Ƙona
Danna "Burn" don fara aiwatar da walƙiya.
StickC-Plus2
Saukewa: K016-P2
Bayani
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Koyarwa
UIFlow
Wannan koyawa za ta gabatar da yadda ake sarrafa na'urar StickC-Plus2 ta hanyar dandamalin shirye-shiryen hoto na UIFlow.
UiFlow2
Wannan koyawa za ta gabatar da yadda ake sarrafa na'urar StickC-Plus2 ta hanyar dandali mai hoto na UiFlow2.
Arduino IDE
Wannan koyawa za ta gabatar da yadda ake tsarawa da sarrafa na'urar StickC-Plus2 ta amfani da Arduino IDE.
Lura
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Siffofin
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Hadakar makirufo
- User buttons, 1.14-inch LCD, power/reset button
- 200 mAh baturi Li-ion
- Mai haɗin haɓakawa
- Integrated passive buzzer
- Wearable & mountable
- Dandalin Ci Gaba
- UiFlow1
- UiFlow2
- Arduino IDE
- ESP-IDF
- PlatformIO
Ya hada da
- 1 x StickC-Plus2
Aikace-aikace
- Na'urori masu sawa
- IoT controller
- STEM education
- Ayyukan DIY
- Smart-home na'urorin
Ƙayyadaddun bayanai
| Ƙayyadaddun bayanai | Siga |
| SoC | ESP32-PICO-V3-02 240 MHz dual-core, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| Shigar da Voltage | 5V @ 500mA |
| Interface | Nau'in-C x 1, GROVE (I2C + I/O + UART) x 1 |
| Allon LCD | 1.14 inch, 135 x 240 launi TFT LCD, ST7789V2 |
| Makirifo | Saukewa: SPM1423 |
| Buttons | Maɓallin mai amfani x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Buzzer | A kan-jirgin m buzzer |
| IMU | Saukewa: MPU6886 |
| Eriya | 2.4G 3D eriya |
| Fil na waje | G0, G25/G26, G36, G32, G33 |
| Baturi | 200mAh @ 3.7V, ciki |
| Yanayin Aiki | 0 ~ 40 ° C |
| Yadi | Filastik (PC) |
| Girman samfur | 48.0 x 24.0 x 13.5mm |
| Nauyin samfur | 16.7g ku |
| Girman Kunshin | 104.4 x 65.0 x 18.0mm |
| Cikakken nauyi | 26.3g ku |
Umarnin Aiki
Kunna/Kashe Wuta
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Tsarin aiki
StickC-Plus2 Tsarin Tsarin PDF
Pin Map
Red LED & IR Emitter | Button A | Button B | Buzzer
| ESP32-PICO-V3-02 | Farashin GPIO19 | Farashin GPIO37 | Farashin GPIO39 | Farashin GPIO35 | Farashin GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Button A | Button A | ||||
| Button B | Button B | ||||
| Button C | Button C | ||||
| Buzzer mai wucewa | Buzzer |
Launi TFT
Driver IC: ST7789V2
Girman: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Nunin TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Microphone MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| Saukewa: SPM1423 | CLK | DATA |
6-Axis IMU (MPU6886) & RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| Eungiyar IR | TX | ||
| Red LED | TX |
Saukewa: HY2.0-4P
| Saukewa: HY2.0-4P | Baki | Ja | Yellow | Fari |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Girman Samfura
Takardar bayanai
ESP32-PICO-V3-02
Saukewa: ST7789V2
BM8563
Saukewa: MPU6886
Saukewa: SPM1423
Softwares
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Saurin Farawa
UiFlow2
StickC-Plus2 UiFlow2 Saurin Farawa
PlatformIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
framework = arduino
upload_speed = 1500000
monitor_speed = 115200
gini_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
Kebul Driver
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Sunan Direba | Supported Chip | Zazzagewa |
| CH9102_VCP_SER_Windows | CH9102 | Zazzagewa |
| CH9102_VCP_SER_MacOS 1.7 | CH9102 | Zazzagewa |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Zazzagewa | Lura |
| Factory Test for Windows | zazzagewa | / |
Sauran
StickC-Plus2 Mayar da Jagorar Firmware Factory
Bidiyo
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Canjin Sigar
| Ranar Saki | Canja Bayani | Lura |
| / | Sakin farko | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Kwatancen Samfur
Banbancin Hardware
| Samfura Suna |
SoC | Gudanar da Wuta | Ƙarfin baturi | Ƙwaƙwalwar ajiya | Kebul-UART Chip | Launi |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| StickC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Lemu |
Bambancin Pin
| Sunan samfur | IR | LED | TFT | BUTTON A | BUTTON B | BUTTON C (WAKE) |
RIKE | Baturi Voltage Gane |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Na yau da kullun maballin |
/ | Ta hanyar AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Bambance-bambancen Kunnawa/Kashe Wuta
| Samfura Suna | Kunna wuta | Kashe Wuta |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Saboda StickC-Plus2 yana cire PMIC AXP192, hanyar kunnawa/kashewa ta bambanta da nau'ikan da suka gabata. Kamar yadda aka ambata a farkon wannan takarda, aikin yana da kama da juna, amma ɗakunan karatu masu goyan baya zasu bambanta. Wi-Fi da ƙarfin siginar IR duk an inganta su idan aka kwatanta da samfurin da ya gabata.
Takardu / Albarkatu
 |
Module Haɓaka M5STACK ESP32-PICO-V3-02 IoT [pdf] Jagorar mai amfani ESP32-PICO-V3-02 Module na haɓaka IoT, ESP32-PICO-V3-02, Module na haɓaka IoT, Module na haɓakawa, Module |