Shigar da JAGORA
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
BAYANI
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
BAYANI
- Mitar rediyo: 2.4 GHz (IEEE 802.15.4)
- Ƙarfin fitarwa na RF: +20dBM
- Zazzabi mai aiki: -40 ° zuwa + 70 ° C
- Humidity na Aiki: 10 zuwa 95%, mara taurin kai
- IP66 An ƙididdige Ƙwararren Ƙwararren
- Girma: 3.1" D x 1.6" H (80mm D x 42mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- Manufar sarrafawa: Aiki
- Environmental: Indoor/Outdoor
- Degree Gurbance: 3
- Tasirin Tasirin Voltagku: 330v
HANYOYIN TSIRA
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltagda 10V DC.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- Hanyar dimming wayoyi daga layin AC idan zai yiwu.
- Matsakaicin 4 DALI-2/D4i LED Direbobi a kowane mai sarrafawa, tuntuɓi Tallafin Synapse idan ana buƙatar babban rabo.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- Kar a hau zuwa heatsink ko zuwa direban LED.
NOTE: Direban LED dole ne ya goyi bayan aikin DIM zuwa KASHE.
GARGADI DA HANKALI
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- Rashin bin waɗannan umarni da gargaɗin na iya yuwu ɓata garanti.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
BAYANIN BAYANIN WAYAR LITTAFI ZHAGA 18 SOCKET
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
HOTO NA 1 
UMARNIN SHIGA
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- Idan an buƙata, cire hular hatimi ko na'urar sarrafa haske da aka shigar a halin yanzu a cikin ma'ajin.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
Lura: Don yin aiki da kyau, tabbatar an shigar da mai sarrafawa gaba ɗaya a cikin soket kuma an karkatar da shi zuwa wurin kulle.
Gargadi: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
HOTO NA 2
MATSAYI LEDS
| Wutar Lantarki | Matsayi |
| Blue | On for 3 seconds at Startup, then Off |
| Matsayin LED | Matsayi |
| Ja | No script on the device |
| Ja mai kiftawa | Kuskuren Sadarwa |
| Blue mai kyalli | Communication, No Config |
| Koren Kiftawa | Normal Operation with Motion |
| Kashe | Normal Operation, no Motion |
BAYANIN HUKUNCI DA TABBAS
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Takaddun shaida na Masana'antu Kanada (IC): Wannan na'urar dijital ba ta wuce iyakar Ajin B don fitar da hayaniya ta rediyo daga na'urar dijital da aka tsara a cikin Dokokin tsoma bakin Rediyo na Sashen Sadarwa na Kanada.
Takaddun shaida na FCC da bayanan tsari (Amurka kawai)
FCC Sashe na 15 Class B: Wannan na'urar ta bi sashe na 15 na dokokin FCC. Aiki yana ƙarƙashin sharuɗɗa biyu masu zuwa: (1) Waɗannan na'urori na iya haifar da tsangwama mai cutarwa, kuma (2) Dole ne waɗannan na'urori su karɓi duk wani tsangwama da aka karɓa, gami da tsangwama wanda zai iya haifar da aiki mai cutarwa.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- Sashe na 15, Ƙarshen B, don kayan aikin Class B
- FCC 96-208 kamar yadda ya shafi kwamfutoci masu zaman kansu na Class B da kayan aiki
- An gwada wannan samfurin a dakin gwaje-gwaje na waje wanda aka tabbatar da shi bisa ga ka'idodin FCC kuma an same shi ya dace da FCC, Sashe na 15, Iyakokin fitarwa. Ana kunna takaddun file kuma ana samun su daga Synapse Wireless, Inc.
Idan FCC ID na module ɗin da ke cikin wannan shingen samfur ba a iya gani lokacin shigar da shi a cikin wata na'ura, to dole ne wajen na'urar da aka shigar da wannan samfurin a ciki dole ne ya nuna alamar da ke nuni da ruɓaɓɓen FCC ID. Canje-canje (FCC 15.21):
Canje-canje ko gyare-gyare ga wannan kayan aikin da Synapse Wireless, Inc. ba ta amince da shi ba, na iya ɓata ikon mai amfani don sarrafa wannan kayan aikin.
Ƙaddamarwa - alamar kama-da-wane a https://www.synapsewireless.com/about/patents
Don ƙarin koyo ziyarar: synapsewireless.com
TAMBAYOYI
| Samfura | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| Ya ƙunshi ID na FCC | QOQ-GM240P |
| Ya ƙunshi IC | Saukewa: 5123A-GM240P |
| RoHS 3 | 2011/65/EU (2015/863) |
| EU ISA | (EC) No 1907/2006 |
DALI-2 Ingantacciyar Mai Kula da Aikace-aikacen
Takardu / Albarkatu
 |
Synapse CSEN1 Combo Sensor Controller [pdf] Jagoran Shigarwa CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |