Mai ƙididdigewa 5002CC Lab Timer

ALAMOMIN
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

Bayyana NUNAWA ZUWA

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

Lokacin aiki

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

KAFA LOKACIN KISSARA

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

NOTE: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two exampana bayarwa.

Exampshafi na 1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. Danna maɓallin 2.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Exampshafi na 2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. Danna maɓallin 3.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

BAYANI

• Nunawa: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• Ƙaddamarwa: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

NASARA MAI GASKIYA

• A- Channel yana nunawa
• B- Maballin Channel Daya (1).
• C- Maballin Channel Biyu (2).
• D- Maballin Channel Uku (3).
• E- Channel ba lokaci ko nunawa ba
• F- Channel yana lokaci amma ba a nuna shi ba
• Maballin G- Hours (H).
• H- Minutes (M) button
• I – Seconds (S) button

Manuniya Tashar
LCD indicators report the status of each channel.

MAYAR DA BATIRI

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

Bayan shigar da batura, tabbatar da nunin mai ƙidayar lokaci yana aiki akai-akai. Lokacin aiki na lokaci, sassan walƙiya na iya bayyana akan nuni. Idan wannan ya faru kawai sake saitawa ta hanyar cirewa da sake shigar da batura. Kowane saitin batura ya kamata ya wuce shekaru 1 zuwa 2 a ƙarƙashin yanayin al'ada. Nunin LCD zai kasance babu komai lokacin da ake buƙatar maye gurbin batura.

GARANTI

GARANTI, HIDIMAR, KO TUNATARWA
Don garanti, sabis, ko gyarawa, tuntuɓi:

ABUBUWAN DA AKA GANO 12554 Tsohon Galveston Rd. Babban B230 Webster, Texas 77598 Amurka

• Ph. 281 482-1714
• Farashin 281-482
• Imel support@traceable.com
• www.traceable.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

Cat. Lamba 5002
Traceable® alamar kasuwanci ce mai rijista ta Cole-Parmer.

©2020 Traceable® Products. 92-5002-00 Rev. 6 070825

FAQs

Takardu / Albarkatu

Mai ƙididdigewa 5002CC Lab Timer [pdf] Jagorar mai amfani 5002CC Lab Timer, 5002CC, Lab Timer, Mai ƙidayar lokaci

Magana

• Manual mai amfani