TRACEABLE® CONTINUOUS
VISUAL ALARM TIMER
UMARNI
BAYANI
= Audible alarm, audible key confirmation
= Visualalarm,visualkeyconfirmationLOKACIN KARARRAWA
- If the timer is running, press the START/STOP button and then press the
kuma 
buttons simultaneously. The display should read 00 00. - Danna maɓallin button to advance the display, or press the button to decrease the display. (When the display reads 00 00, pressing the button will decrease the display to 99 99.)
- Once the desired time is on the display, press the START/STOP button to begin counting down. During countdown timing, the alarm will sound once (singleflashorbeep)every30secondstoindicatea30 second interval has passed.
- When the display reaches 00 00 the alarm will start (audible or visual depending on the alarm setting) and the timer will begin counting up.
During the first minute of alarming, the timer will alarm with increasing intensity. After the first minute, the timer will continue counting up and will alarm once (a single flash or beep) every 30 seconds until the alarm is stopped. The alarm may be stopped at any time by pressing any button.
While the timer is alarming–
Danna maɓallin
or button will stop the alarm, but will allow the timer to continue counting up.Pressing the START/STOP button will stop the alarm, stop the count up timing and will return the display to the originally programmed time.
TUNATARWA
The memory function will recall the last programmed time. This feature allows the timer to be dedicated to a frequently timed test. The timer will return to the last programmed time again and again.
- Bi matakai na 1 zuwa 4 a cikin sashin "Ƙararrawar Ƙararrawa".
- When the alarm starts, press the START/STOP button to stop the alarm, stop the count up timing and return the display to the originally programmed time.
- Press the START/STOP button again to begin counting down.
GYARA SHIGA
If an error is made during an entry, press the kuma buttons simultaneously to clear the display to zero. Το clear an entry when time is running, stop the timing by pressing the START/STOP button, then press the kuma buttons simultaneously. The timer will only clear when time is stopped.
TSAYAWA (ƙidaya-UP) LOKACI
2. Press the START/STOP button to begin count-up timing.
Note: During the first 99 minutes 59 seconds of count-up time, the resolution is 1 second, after 100 minutes, the count-up resolution is 1 minute.
3. When timing has been completed and the timing has been stopped, press the and buttons simultaneously to clear the display to zero.
LOKACI
If this timer does not function properly for any reason, replace the batteries with new high quality batteries (see “Battery Replacement” section). Low battery power can occasionally cause any number of “apparent” operational difficulties. Replacing the batteries with a new fresh battery will solve most difficulties.
MAYAR DA BATIRI
An incorrect display, no display or operational difficulties indicate that the batteries should be replaced. Slide open the battery cover on the back of the timer. Insert two new AAA size batteries. Make certain to note the proper polarity as indicated by the diagram in the battery compartment. Replace battery cover.
GARANTI, HIDIMA, KO HALITTA
Don garanti, sabis, ko daidaita lamba:
ABUBUWAN DA AKA GANO
12554 Tsohon Galveston Rd. Babban B230 Webster, Texas 77598 Amurka
Ph. 281 482-1714
Farashin 281-482
Imel support@traceable.com
www.traceable.com
Traceable Products are ISO 9001:2015 Quality-Certified by DNV and ISO/IEC
17025: 2017 wanda aka amince da shi azaman Laboratory Calibration ta A2LA.
Traceable and is a registered trademark of Cole-Parmer.
©2020 Abubuwan da za a iya ganowa. 92-5133-00 Rev. 5 071525
Takardu / Albarkatu
 |
Visual Traceable 5133 Alarm Timer [pdf] Jagorar mai amfani 5133, 6876af4336218, 5133 Alarm Timer, 5133, Alarm Timer, Timer |